En Original Instructions; Declaration Of Conformity; Specified Use; General Safety Instructions - Metabo MBS 18 LTX 2.5 Manual Original

Original Instructions

1. Declaration of Conformity

We hereby declare under our sole responsibility
that these cordless band saws, identified by type
and serial number *1), meet all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see page 4.

2. Specified Use

This cordless band saw can be used to cut metal
and hard plastic. The material to be sawed must
rest on a firm surface. The cordless band saw is
suitable for straight cutting with a mitre angle of up
to 45°. Please note the saw blade
recommendations.
Do not saw any plastics that may melt due to the
frictional heat. Cutting melting plastics may lead to
a burnout of the motor due to overloading.
The light on this cordless band saw is used to light
the immediate operating range of the power tool
and must not be used as a torch or for room lighting.
The cordless band saw must not be used in a wet
environment or near flammable liquids or gases.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

Pay attention to all parts of the text that
are marked with this symbol for your own
protection and for the protection of your
power tool!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in an electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.

4. Special Safety Instructions

Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessories contacting a „live" wire
may make exposed metal parts of the power tool
„live" and could give the operator an electric shock.
WARNING – Always wear protective
goggles.
Always wear protective goggles, work gloves and
sturdy shoes when working with this tool.
Wear ear protectors when working for long
periods of time. High noise levels over a
prolonged period of time may damage your hearing.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
When sawing water pipes, ensure that they do not
contain any water.
Use only sharp, undamaged saw blades. Do not
use saw blades that are cracked or that have
changed their shape.
Always hold the tool with both hands on the
designated handles, take a secure stance and
concentrate on the work.
Work only with the parallel guide attached.
When sawing, the parallel guide must make secure
contact with the workpiece.
Do not try to saw extremely small workpieces.
Clamp the workpiece properly e.g. using clamping
fixtures. Under no circumstances should you hold
the workpiece with your hand or foot.
Keep your hands away from the sawing area and
from the saw blade.
Risk of injury due to the sharp saw blade.
Do not touch the moving saw blade!
Remove shavings and similar material only with the
tool at a standstill.
The saw blade and shavings may be very hot after
sawing. Wear protective gloves.
LED light (11): Do not observe the LED radiation
directly with optical instruments.
Never use an incomplete tool, or one on which an
unauthorised modification has been made.
Do not switch on the tool if parts or guard devices
are missing or defective.
Guide the tool against the workpiece only when it is
switched on. Otherwise there is a risk of rebound
from jamming the tool in the workpiece.
Switch off the tool after completing the cutting and
let the saw blade come to a standstill. Only then pull
the saw blade out of the cut. This prevents any
rebound.
Keep oil and lubricant away from the saw blade.
Wipe off any excess oil completely before cutting
otherwise the saw blade may slip.
Do not exert excessive pressure on the saw blade
when working. The saw blade may slip or break if
excess pressure is exerted.
Do not slow down the saw blade after switching off
the tool by pressing it against the side of the
workpiece. Otherwise the saw blade may break or
ENGLISH en
11