Cub Cadet CC 30 Manual Del Operador página 19

Setting the Cutting Height
1. Select the height position of the cutting deck by placing
the deck lift lever in any of the different cutting height
notches on the right side of the fender.
WARNING!
Keep hands and feet away from the
discharge opening of the cutting deck.
Refer to Leveling the Deck in the Maintenance & Adjustments
section of this manual for more detailed instructions regarding
deck adjustment.
Starting the Engine
WARNING!
Do not operate the tractor if the
interlock system is malfunctioning. This system was
designed for your safety and protection.
NOTE: Refer to the Assembly & Set-Up section of this manual for
gasoline and oil fill-up instructions.
1. Insert the tractor key into the ignition switch module.
2. Place the PTO (Blade Engage) lever in the disengaged (OFF)
position.
3. Engage the tractor's parking brake.
4. Activate the choke control by moving the throttle/choke
control all the way forward into the choke position.
5. Turn the ignition key clockwise to the START position.
After the engine starts, release the key. It will return to the
NORMAL MOWING position.
CAUTION:
Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing
so may cause damage to your engine's electric
starter.
6. After the engine starts, deactivate the choke control by
placing the throttle control into the FAST position.
NOTE: Do NOT operate this unit with the Choke control
activated. Doing so will result in a "rich" fuel mixture and can
cause the engine to run poorly.
Stopping the Engine
WARNING!
If you strike a foreign object, stop the
engine, disconnect the spark plug wire and ground
against the engine. Thoroughly inspect the machine
for any damage. Repair the damage before
restarting and operating.
1. If the blade is engaged, place the PTO (Blade Engage) lever
in the disengaged (OFF) position.
2. Place the throttle/choke control near the SLOW position.
3. Turn the ignition key counter-clockwise to the STOP
position.
4. Remove the key from the ignition switch to prevent
unintended starting.
Driving the Tractor
WARNING!
Avoid sudden starts, excessive speed
and sudden stops.
WARNING!
Do not leave the seat of the tractor
without first placing the PTO (Blade Engage) lever
in the disengaged (OFF) position, depressing the
clutch-brake pedal and engaging the parking brake.
If leaving the tractor unattended, also turn the
ignition key OFF and remove the key.
WARNING!
Always look down and behind before
and while backing up to avoid a back-over accident.
1. Move the throttle lever into the FAST (rabbit) position.
2. Place the shift lever in either the FORWARD or REVERSE
position.
3. Depress the clutch-brake pedal and move the speed
control lever out of the parking brake position and into the
desired speed setting.
5. Release clutch-brake pedal slowly to put unit into motion.
6. The lawn tractor is brought to a stop by depressing the
clutch-brake pedal.
IMPORTANT: Do NOT use the shift lever to change the direction
of travel when the tractor is in motion. Always use the clutch-
brake pedal to bring the tractor to a complete stop before
shifting.
IMPORTANT: First-time operators should use speed positions 1
or 2. Become completely familiar with the tractor's operation and
controls before operating the tractor in higher speed positions.
NOTE: When operating the unit initially, there will be little
difference between the highest two speeds until after the belts
have seated themselves into the pulleys during the break-in
period.
WARNING!
Before leaving the operator's position
for any reason, disengage the blade, place the shift
lever in neutral, engage the parking brake, shut
engine OFF and remove the key.
IMPORTANT: When stopping the tractor for any reason while on
a grass surface, always:
1. Place the shift lever into neutral.
2. Engage the parking brake.
3. Shut the engine OFF and remove the key. Doing so will
minimize the possibility of having your lawn ''browned'' by
hot exhaust from your tractor's running engine.
If unit stalls with speed control in high speed, or if unit will
not operate with speed control lever in a low speed position,
proceed as follows:
1. Place shift lever in NEUTRAL.
2. Restart engine.
3. Place speed control lever in highest speed position.
4. Release clutch-brake pedal fully.
5. Depress clutch-brake pedal.
6. Place speed control lever in desired position.
7. Place shift lever in either FORWARD or REVERSE, and follow
normal operating procedures.
S 5 — o
ection peration
19