Hints For Otr And Timer Recording - Sanyo DVW-7200 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5
5
Select the desired start time
(hour).
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
or
START TIME 0 7 : 3 0 – –
END
TIME – – : – – – –
CHANNEL
REC SPEED – –
Select the minute.
or
6
6
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
START TIME 0 7 : 3 0 PM
END
TIME – – : – – – –
or
CHANNEL
REC SPEED – –
Select "AM" or "PM".
7
7
Repeat the procedure in steps
5) and 6) to set the end time.

Hints for OTR and Timer Recording

• Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR
mode, then press [SUBTITLE/T-SET].
• If a tape is not in the unit or does not have the record tab, the TIMER REC light flashes and Timer Recording cannot be
performed. Please insert a recordable tape.
• When Timer Recordings are set, the TIMER REC light will appear. To use the VCR as usual until the time for the recording,
press [SUBTITLE/T-SET] so that the TIMER REC light disappears. Press [VCR/TV] to select the VCR position. Select
either VCR or DVD mode, then continue with the other features as described in this manual.
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape and switches to the DVD mode
automatically. If the DVD power is off, the unit does not switch to the DVD mode but goes into the timer standby mode.
Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C/A] on the unit, then press [VCR] to activate the VCR
function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed.
([OUTPUT] on the front panel and [VCR] on the remote control will not function.)
• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C/A] on the unit, then
press [VCR] to activate the VCR function again.
• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after
you cancelled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you
operate.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically,
and the TIMER REC light on the front panel appears to indicate the unit is in the timer standby mode.
• The TIMER REC light on the front panel flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR function will be
unavailable. The TIMER REC light will not appear as long as the DVD is in use. All the DVD functions are available during
OTR, timer standby mode and Timer Recording.
If you want to use the DVD player during a timer recording or while the TIMER REC light appears or flashes...
• Press [POWER] to turn on the DVD. Press [DVD] on the remote control to select DVD mode, then continue with the other
DVD features as described in this manual. You don't need to set the TIMER off to use the DVD player.
NOTE (for Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
8
8
or
1 0 / 2 4 MON
– –
• If you have connected the unit to a cable
box or satellite box as the Connection A
on page 6, select the VCR to channel 3
or 4 (the RF output channel of the VCR).
Then, select the desired channel at the
cable box or satellite box. Leave the
cable box or satellite box on for timer
recording.
9
9
or
1 0 / 2 4 MON
– –
AM
Select the desired recording speed.
B PM
• To set another program after step 9), press
[B]. Then, continue with step 2).
10
10
SUBTITLE
T-SET
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END
TIME 0 8 : 3 0 PM
CHANNEL
1 6
REC SPEED – –
Select the desired channel.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 4 MON
START TIME 0 7 : 3 0 PM
END
TIME 0 8 : 3 0 PM
CHANNEL
1 6
REC SPEED SP
B SP
SLP
CLEAR /
C.RESET
• The TIMER REC light on
the front panel appears.
The unit will change to
the DVD mode.
– 13 –
Hint
Hint
• To go back one step, press [
s
the steps 3) to 9) ).
To Check, Correct or Cancel a
Timer Program
1) Press [SUBTITLE/T-SET], then
press [VCR] on the remote control.
2) Select main menu by pressing
[MENU].
3) Press [K] or [L] to select "TIMER
PROGRAMMING
, then press [B].
"
4) Press [K] or [L] to select the pro-
gram number which you want to
check. The details of the program
you selected will appear on the TV
screen.
• Press [s] or [B] to go to the digit
you want to change, then, press [K]
or [L] to enter correct numbers.
• You may cancel the entire program
by pressing [s] while the program
number flashes.
5) Press [CLEAR/C.RESET] to exit.
6) Press [SUBTITLE/T-SET] to return
to timer stand-by mode.
To cancel a Timer Recording
in progress
Press
STOP/EJECT C C /A A
[
unit.
] (during
on the
]
EN

Publicidad

Tabla de contenido
loading

Tabla de contenido