Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Connections
Please refer to "Basic TV Connection" on the front page before you use this unit.
RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [OUTPUT] on the unit so that the VCR
OUTPUT light is lit.
• If noise appears on the TV screen, press
[VCR/TV] on the remote control.
4) Press [PLAY B] once.
Hints for Cable Box or Satellite Box
Connection A
(Cable box or
Satellite box)
Antenna or
IN
cable TV
OU T
signal
Select this connection when you want to view or record a scram-
bled channel. With this connection, channels cannot be changed
on the unit. You can view or record ONLY the channels you have
selected on the cable box or the satellite box.
• While you are recording, only the recorded channel can be
viewed.
To select channels of the cable box or satellite box
1) Turn on the unit by pressing [POWER
The "POWER" light on the front panel will appear, then press
[SKIP/CH. i
i /K K j
j /L L
]
to select channel 3 or 4 (the same
channel as the output channel of the cable box or satellite
box).
• If you use the channel 4, you need to change the unit's RF
output to channel 4. Refer to "RF Output Channel".
2) On the TV, select channel 3 or 4 (the same channel as you
)
have selected at step 1
.
3) On the cable box or satellite box, select the channel you want
to view or record.
Connection to an Audio System
Method 1
Stereo system
AUDIO
Audio cable
(supplied)
DVD+VCR
AUDIO OUT
(Analog)
AUDIO OUT
Connection
Connecting to Stereo System.
* To complete these settings, refer to pages 20-21.
Hint
Hint
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
Need help? Call
1-800-813-3435
5) After a few seconds, press [PLAY B B ] on
the unit for 3 seconds.
• The RF output channel will change to
channel 4 from channel 3 and you will
see a playback picture.
• When a picture does not appear on the
TV screen, repeat step 4).
6) Press [STOP C] to stop playback.
(Back of DVD+VCR)
ANT-IN
E
ANT-OUT
RF cable
(supplied)
(Back of TV)
]
, then press [VCR/TV
Analog audio
L
R
input jacks
DVD
DVD/VCR
VCR
DIGITAL
COMPONENT
AUDIO OUT
AUDIO
S-VIDEO
VIDEO OUT
OUT
OUT
L
L
or
R
R
(DVD mode only)
Setting
SETUP > AUDIO menu >
DOLBY DIGITAL
PCM
Setup
Connection B
Antenna or
cable TV
signal
RF cable
Select this connection when you want to change channels on the unit. With
this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box
1) On the cable box, select channel 3 or 4 (the same channel as
the unit's RF output channel).
• Refer to "RF Output Channel".
]
.
2) On the TV, select the same channel as the output channel (3
or 4) of the cable box.
3) Turn on the unit by pressing [POWER
The "POWER" light on the front panel will appear, then select
the channel you want to view or record.
To play back a tape
)
Follow the steps 1
to 2
• Refer to "Playback" on page 11.
To view one channel while recording another
1) While you are recording on the unit, press [VCR/TV
2) On the cable box, select the channel you want to view.
Dolby Digital decoder,
MD deck or DAT deck
Audio Coaxial
Digital cable
(commercially
available)
DIGITAL
AUDIO OUT
Connection
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
Connecting to the other equipment (an MD deck
or DAT deck etc.) without Dolby Digital decoder.
* To complete these settings, refer to pages 20-21.
Hint
Hint
• The audio source on a disc in a Dolby Digital 5.1 channel surround
format cannot be recorded as digital sound by an MD or DAT deck.
• By hooking this unit up to a Multi-channel Dolby Digital
decoder, you can enjoy high-quality Dolby Digital 5.1
channel surround sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate
noise distortion and may also damage the speakers.
– 6 –
Hint
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In this
case, stop the playback, and
start the playback again. After
that, press [PLAY B B ] on the
unit for 3 seconds again.
(Back of DVD+VCR)
ANT-IN
(Cable box)
ANT-OUT
IN
OU T
(Back of TV)
RF cable
(supplied)
]
, then press [VCR/TV
)
above, then play back a tape.
]
Method 2
COAXIAL
Digital audio
input jack
DVD
DIGITAL
COMPONENT
AUDIO
S-VIDEO
VIDEO OUT
AUDIO OUT
OUT
OUT
COAXIAL
Setting
SETUP > AUDIO menu >
DOLBY DIGITAL
BITSTREAM
PCM
E
]
.
.
EN
Publicidad
Tabla de contenido
