Technical Data; Filling The Magazine; Noise/Vibration Information - KMR 3516 Datos Tècnicos, Piezas De Repuesto

4 I English
1

TECHNICAL DATA

Type Type
Type Type
Dimensions mm
Weight kg (without fasteners)
Single sequential or contact actuation
Recommended operating pressure
range
Maximun permissible operating
pressure
Air consumption per driving
operation
Magazine capacity.
No. of fasteners
Penetration depth setting
Fasteners: Wire Fasteners: Wire bound bound nail
Fasteners: Fasteners: Wire Wire bound bound
Nail length mm
Head diam. Ø mm
Recommended lubricant Recommended lubricant
Recommended Recommended lubricant lubricant
1 litre special oil. Code No.
250 cm3 grasa especial. Code No.
2

NOISE/VIBRATION INFORMATION

Noise characteristic Noise characteristic values
Noise Noise characteristic characteristic
A-weighted single-event emission
sound pressure level at work
station L pA, 1s
A-weighted sound power level
L WA, 1s, d
Vibration Vibration Vibration Vibration characteristic characteristic values characteristic characteristic
Weighted r.m.s.-acceleration (a)
The noise level when working can exceed 85
db (A). Wear Wear ear Wear Wear ear protection! ear ear
* Measured values determined according to
EN 12549:1999.
** Measured values determined according to
ISO 8662-11:1999.
3 SUPPLIED WITH
1 Coil nailer
1 Tool use and safety instructions
1 Technical data sheet
KMR
3516 3516
3516 3516
270/255
2,3 kg
4 - 8 bar/0,4 -
0,8 MPa
8,5 bar / 0,85
MPa
1,6 l at
6 bar / 0,6 MPa
120
yes
nail coils coils
nail nail coils coils
19-45
10,5
9 4420
68 3868
values * * * * 3516 3516
values values 3516 3516
87 dB(A) 87 dB(A)
87 87 dB(A) dB(A)
100 dB(A) 100 dB(A)
100 100 dB(A) dB(A)
values ** values values ** ** **
2,5 m/s2 2,5 m/s2
2,5 2,5 m/s2 m/s2
protection! protection! protection!
4

FILLING THE MAGAZINE

Only those fasteners specified under technical data
(see 1) may be used.
When filling the magazine, hold the tool so that the
muzzle is not pointing towards own body or towards
any other person.
Do not load the tool with fasteners with the safety
yoke or trigger depressed.
To open the magazine, open the guide flap (k) using
the notch lever (l) and swing open the magazine cover.
The spring mounted support plate (n) can be adjusted
and fixed at 3 levels (a scale for the corresponding
nail lengths can be found in the bottom part of the
magazine). Insert the nail coil in such a way that the
beginning of the coil is in the driver channel. Close the
magazine cover and lock the guide flap.
5 FIL PENETRATION DEPTH SETTING
The penetration depth of the nail head is adjusted
using air pressure. Should this not suffice, a more
exact setting of the penetration depth can be achieved
by turning the setting nut (p).
Right-hand turn (U) = less penetration depth.
Left-hand turn (D) = more penetration depth.
6 SWITCHABLE ACTUATION
-SINGLE TRIGGER RELEASE/RELEASE ON CONTACT-
A setting wheel on the trigger (s) can be turned to set
the type of actuation either to single trigger release
or release on contact (see symbol).
7 ACCESSORIES
Balancer for 20-30 N (2.0-3.0 kp),
cable travel 2.0 m (6.5 ft)
3516
Code No.
40 3407