Publicidad
Idiomas disponibles
Idiomas disponibles
Briggs & Stratton Generac Generator Discount Parts Call 606-678-9623 or 606-561-4983
MAINTENANCE
SPECIFICATIONS
Max Outlet Pressure . . . . . . . . . . . . . . . . . . . . . 2600 psi
Max Flow Rate . . . . . . . . . . 2.5 gallons per minute (gpm)
Detergent Use detergent approved for pressure washers
Water Supply . . . . . . . . . . . . . . . . Not to Exceed 100°F
Temperature
Automatic Cool . . . . . . . . . . . . . Will cycle when water
Down System
Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . .70 lbs.
GENERAL MAINTENANCE
RECOMMENDATIONS
The pressure washer warranty does not cover items that
have been subjected to operator abuse or negligence.To
receive full value from the warranty, the operator must
maintain the pressure washer as instructed in this manual.
NOTE: Should you have questions about replacing
components on your PowerBOSS™ pressure washer,
please call 1-800-743-4115 for assistance.
• Some adjustments will need to be made periodically to
properly maintain your pressure washer. Check the spray
gun and nozzle extension assembly for wear.
• All maintenance in this manual and the engine operator's
manual should be made at least once each season.
• If equipped with inflatable tires, keep the air pressure at
the value marked on the tire or within 15 and 40 psi.
Before Each Use
1.
Check engine oil level.
2.
Check water inlet screen for damage.
3.
Check in-line filter for damage.
4.
Check high pressure hose for leaks.
5.
Check chemical injection hose and filter for damage.
6.
Check spray gun and nozzle extension assembly for leaks.
7.
Rinse out garden hose to flush out debris.
PRESSURE WASHER
MAINTENANCE
Check and Clean Inlet Screen
Examine the screen on the water inlet. Clean it if the
screen is clogged or replace it if screen is damaged.
2600 PSI Pressure Washer
reaches 125°-155°F
www.mymowerparts.com
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before using
it. Check for cuts, leaks, abrasions or bulging of cover,
damage or movement of couplings. If any of these
conditions exist, replace the hose immediately.
WARNING
The high pressure stream of water that this
equipment produces can pierce skin and its
underlying tissues, leading to serious injury and
possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST exceed maximum pressure
rating of unit.
Check Detergent Siphoning Tube
Examine the filter on the detergent tube and clean if
clogged.The tube should fit tightly on the barbed fitting.
Examine the tube for leaks or tears. Replace the filter or
tube if either is damaged.
Check Gun and Nozzle Extension
Examine the hose connection to the spray gun and make
sure it is secure.Test the trigger by pressing it and making
sure it "springs back" into place when you release it. Put
the trigger lock in the ON position and test the trigger.You
should not be able to press the trigger.
Check In-Line Filter
Refer to Figure 14 and service the in-line filter if it
becomes clogged, as follows:
Figure 14 — Clean In-Line Filter
Nozzle Extension
1.
Detach spray gun and nozzle extension from high
pressure hose. Detach nozzle extension from spray
gun and remove o-ring and screen from nozzle
extension. Flush screen, spray gun, and nozzle
extension with clean water to clear debris.
2.
Place in-line filter screen into threaded end of nozzle
extension. Direction does not matter. Push screen in
with eraser end of pencil until it rests flat at bottom of
opening.Take care to not bend screen.
13
PowerBOSS™
Filter Screen
O-ring
Publicidad
