mundoclima R51M/(C)E Instrucciones De Instalación página 13

Remote Controller Specification
Model
R51M/(C)E, R51M/BG(C)E, RG51M2/(C)E,
RG51A/(C)E, RG51M3/(C)E.
R ated Voltage
3.0V (Alkaline dry batteries LR 03 2)
Lowest Voltage of CPU
2.0V
Emitting Signal
8m (when using 3.0 voltage,
Transmission Distance
it Gets 11m)
"
Environment
-5 C 60 C
Performance Features
1. Operating Mode: AUTO COOL !
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~ 30 C.
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting(only available for R51M/BG(C)E models)
Features of the Remote controller buttons
( C)
SET T EMPERATURE
FAN
AUTO
HIGH
COOL
MED
DRY
LOW
HEAT
TEMP
1
ON/OFF
MODE
FA N SPEED
3
TIMER ON
SW ING SLEEP
4
TIME R OFF
5
RESET LOCK
AIR CLEAN
LED
DIRE CTION AIR
DISPLAY TU RBO
6
*
7
Fig. 1
TEMP But ton : Push this button to decrease the indoor
1
temperature setting.
TEMP Butt on : Push this button to increase the indoor
2
temperature setting .
MODE Sel ection Butt on: Each time the button is pressed, the
3
operation mode is shifted in the direction of the arrow:
AUTO CO OL
NOTE: COOL only model has no HEAT feature.
4
SWING But to n: Push this switch button to a ctivate auto
swing feature of the horizontal louver. P ush it aga in to stop.
RESET B utt on : When you press the recessed RESET button,
5
all current settings are cancelled and the control will return to
the initial settings.
6
A IR DIRECTION Button: Press this button to change the swing
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would a utomatically change the swing direction . No symbol
will appear in the display area when press this button. (Not
applicable to units without this function).
LED DISPLAY But ton: Press this button to clear the digit
7
display in the air conditioner, press it again to activate it (Not
available for the units without LED display window).
8 FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW ! ! MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
ON/OFF Button: Push this button to start operation, push the
9
button again to stop operation.
TIMER ON B utt on: Press this button to initiate the auto-on time
10
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0:00.
SLEEP B ut ton : Press this button to go into the Energy-Saving
11
operation mode. Press it again to cancel. T his function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the other button.
#
"
! DRY !
" "
NO TE:
: Indicates optional
*
button.
2
M odels R G51M2/(C)E:
9
*
without 14 and 15 *
8
buttons.
10
Models RG 51M3/(C)E:
11 * *
without 7 , 14 and
*
15 buttons.
12
13 Models R51M/(C)E
and R 51M/BG(C)E :
14 *
*
without 15 button.
15 *
DR Y HEAT FAN
o
TIMER OFF But ton: Press this button to initiate the auto-off time
12
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10:00, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time
to 0:00
L OCK B ut ton: When you press the recessed LOCK button, all
13
current settings are locked in and the remote controller does not
accept any operation except that of the LOCK. Press again to
cancel the LOCK mode.
14 TURB O Bu tt on : Push this button to activate/cancel the Turbo
function which enables the unit to reach the preset temperature in
the shortest time.On cooling mode, the unit will blow strong cooling
air with super high fa n speed. On heating mode (applicable to the
unit adopts PTC only), the P TC will bring fast heating operation.
15 CLEAN A IR Bu tto n(on som e m odel s): When push this button,
the Ionizer or P lasma Dust Collector(depending on models) is
energized and will help to remove pollen and impurities from
the air.
Indicators on Display Panel
1
DIGI TAL
D ISP LAY area
TRA NS MI-
2
SS ION Indicator
O PERAT ION
4
MO DE Indicator
5
LO CK Indicator
TIMER 6
DISPLAY Indicator
DIGITA L DISPL AY area: T his area will show the set temperature
1
and, if in the TIMER mode, will show the ON and OFF settings of
the TIMER. If in the FAN mode, nothing is appeared.
2 TRANSMISSION Ind ic ato r: This indicator flashes one time
when remote controller transmits signals to the indoor unit.
ON/OFF Indi cator : This symbol appears when the unit is turned
3
on by the remote controller, and disappear when the unit is
turned off.
OPERATION MODE Indi cator : When press the MODE button,
4
it shows the current operating mode -- AUTO
" HEAT (Cooling only model without) "
LOCK Indi cat or : LOCK display is displayed by pushing the LOCK
5
button. Push the LOCK button to clear display.
TIMER DISPLAY Indicator: T his display area shows the settings
6
of the T IMER . T hat is, if only the starting time of operation is set,
it will display the T IMER ON. If only the turning off time of opera tion
is set, it will display the TIMER OFF. If both operations are set,
it will show T IMER ON-OFF which indica tes you have chosen
to set both the starting time and off time.
FAN SPEED Indicator: Press the FAN SPEED button to select
7
the desired fan speed setting (Auto-Low-Med-High). You selection
will be displayed in the LCD window except the Auto fan speed.
NOTE: All signs shown in the Fig.2 is for the purpose of clear
presentation. But during the actual operation only the re-
lative functional signs are shown on the display panel.
Operating the Remote Controller
Install/Replace Batt eries
The Remote Controller uses two alkaline dry batteries
1. To install the batteries, slide the back cover of the battery
compartment and install the batteries according the
direction (+ and -)shown on the Remote Controller.
2. To replace the old batteries, use the same method as
mentioned above.
NOTE
1. When repla cing batteries, do not use old batteries or a different
type battery. This may cause the remote control
to malfunction.
2. If you do not use the remote controller for several weeks
remove the batteries. Otherwise battery leakage may damage
the remote controller.
3. The average battery life under normal use is about 6 months.
4. R eplace the batteries when there is no answering beep from the
indoor unit or if the Transmission Indicator light fails to light.
5. Do not dispose batteries as unsorted municipal waste. Collection
GB
of such waste separately for special treatment is necessary.
Display Panel
3
O N/O FF Indicator
4
OPER ATION
MODE Indicator
7
FAN SPE ED Indicator
TIMER ON OFF
Fig. 2
" " , " COOL
, or " FAN" mode.
(LR03X2).
" , " DRY ",