Hunter All-Fan 27186 Manual Del Usuario

All-Fan ™ 2-Wire Fan & Light Control
Model 27186
Read and Save these Instructions
Caution: Risk of Electrical Shock!
All wiring must be performed in accordance with national and
local electrical codes. If you are unfamiliar with the wiring
codes, you should use a qualified electrician.
To avoid overheating and possible damage to other equip-
ment, do not install to control a receptacle, fluorescent light
fixture, motor operated appliance, or transformer-supplied
appliance. Use only to control one paddle-blade ceiling fan
and incandescent light fixture.
Notes:
1. This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including inter-
ference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
3. For use only with electrically reversible ceiling fans rated at 1.0 amp or less,
and fan incandescent light kits rated at 300 watts or less.
4. Not for use with shaded-pole or non-reversible motors. Not recommended
for use with the Hunter Original ® . For Hunter Original
control model numbers 22798 or 26591.
5. Medium and Low fan speeds are determined by the All-Fan
may vary from the factory settings due to normal motor variations.
Wall Control Installation:
1. Remove rocker style wallplate (not included) to expose the wall wiring.
Disconnect the existing switch and remove from the electrical box.
2. If 4 wires are visible, connect each black wire to an All-Fan
If 2 wires are visible, connect each to an All-Fan
nuts supplied to make the connections. Refer to Figure 2.
3. If a ground wire is provided in your electrical box, attach it to the ground
screw near the bottom of the mounting plate.
4. Gently push wires and wall control into the electrical box. Attach the All-Fan
control to the switch box with the two screws provided.
5. Verify that the master switch is in the OFF Position. Press inward on each side
of the wall control to remove face cover. Set the dip switches to match the dip
switches in the receiver. Install a 12 volt alkaline battery (A23, MN21, or equiv-
alent). Replace the face cover.
Figure 1
Dip Switch
ON DIP
1 2 3
Select your own unique code, being sure settings match in the
transmitter and receiver.
® series fans, use Hunter
™ control and thus
™ black black wire.
™ lead. Use 2 of the large wire
™
Transmitter Back
4
Operation:
1. Slide the master switch to the ON position, the light will turn ON at maximum
brightness.
2. Light Operation:
• Press and quickly release the light button on the wall mounted control to turn
the light OFF or ON. (Light will come ON at maximum brightness.)
• Press and hold the light button for more than 1 second to turn the light ON
and decrease from maximum brightness to OFF.
• Release the light button when the desired light level is reached.
• Continue to hold the light button to repeat the cycle. (Maximum–light level
decrease–OFF)
• While the light is ON, holding the light button will decrease the light brightness.
• Turning the light OFF resets the dimming function. The next press of the light
button will start at maximum brightness.
3. Fan Operation:
• Press the High, Medium, or Low speed buttons to turn the ceiling fan ON at
the desired speed.
• Press the fan OFF key to turn the ceiling fan OFF.
For best fan operation: Allow the ceiling fan motor to start on High, then select
the desired speed.
4. Manual Light Switch Operation:
To turn the lights ON without battery power to the wall control turn OFF the
wall switch for 5 seconds, then turn the master switch back ON. The light will
turn ON at maximum brightness, and the fan will be OFF.
For everyday operation, leave the master switch ON. However, if the control will
not be used for an extended period of time (5 days or more), turn the master
switch OFF.
Figure 2
Light Button
Fan OFF
Fan Low Speed
Fan Medium Speed
Fan High Speed
Master ON/OFF
2001, Hunter Fan Company
41541-01 11/12/2001