Caller Identification - Vimar ELVOX 68IG/R Instrucciones Instalador

Kit Due Fili
CH2
CH1
BS
ID1
ID0
Phone identification code
When on the intallation there is more than
Interphone
CODICE
ID1 ID0
code
IDENTIFICAZIONE one phone it is necessary to identify the
(D) identification
(E)
ID 0
CITOFONO
phone with a different code. The identifica-
tion code is assigned by inserting the jump-
n°1
ID 1
ers in contacts D and E (ID1 and ID0) as
indicated in the figure.
n°2
n°3
n°4
Intercommunicating call programming
Programming of the intercommunicating call pushbuttons (terminals 10,
11, 12) is automatic on assignment of the interphone identification code
as shown in the table below.

Caller identification

code (n°)
Terminals Call receiver identification
code (n°)
10
11
12
Lock release
Removing contact BS from the phone it is possible to open the door lock
always, with phone inserted from the call or not.. Inserting the jumper, it is
possible to release the door lock from the phone only after the call or has
been self-activated.
Association of call push-button from the entrance panel
To associate the panel pushbutton used to call the interphone, set con-
tacts A (CH2) and B (CH1) accordingly:: contact B for the right hand panel
push-button or 1° push-button and contact B for the left hand push-button
or 2° push-button. Inserting the jumpers the call is excluded, removing them
the call and the phone activation is enabled.
CH2
CH1
APERTURA SERRATURA SEMPRE
Jumper missing
LOCK RELEASE ALWAYS
8
1 2
Jumper missing
Jumper inserted
1 2 3 4
2 1 1 1
3 3 2 2
4 4 4 3
Jumper inserted
Operation
Interphone/monitor type 62I8+6029 (62I8+6029/C) can call other interphone
types 62I8+6029 (62I8+6029/C) or monitor types 6328 (6328/C) according
to the table above, but monitor types 6328 (6328/C) cannot call interphone
types 62I8.
To make an intercommunicating call, lift the handset and press the inter-
communicating button for the interphone/monitor to be called; the maximum
duration of the conversation is 60 seconds. During an intercommunicating
conversation (or with the handset already raised) the calls from the entrance
panel do not switch the conversation automatically and the auto-start/self-
start button must be pressed (without replacing the handset) to communi-
cate with the entrance panel. The conversation time between the entrance
panel and interphone can be set from 30 to 90 seconds, after which the
interphone must be called from the entrance panel within 10 seconds to
proceed conversation without replacing the handset; otherwise press the
auto-start/self-start button on the interphone.
If required operate the electric lock by pressing proper push-button
. The monitor turns off after nearly 30'' (adjustable on the panel from 30 to
90 seconds). The installation can be switched on by pressing the push-but-
ton connected to terminal 9, thus allowing an external view when required.
When two cameras are installed, both cameras are cyclically activated on
pressing the push-button.
N.B.: the intercommunicating call is generated with a different ringtone from
other calls and the duration depends on activation of the call pushbutton.
The selfstart/selfinsertion push-button allows the connection of interphone
or monitor to the entrance panel without being called. If there are two en-
trance panels on the installation, the repeted pressure of the selfstart/selfin-
sertion push-button switches the panel selection cyclically.
VIDEO SIGNAL STABILISATION
A connector and jumper are located inside the interphone for stabilisation
of the video signal (see fig. 3); this jumper must be used in the following
cases:
in systems with multiple devices (interphones or monitors) connected in
series. Move the jumper of the last device only to position BC and keep the
other jumpers in the initial position (AB) (Fig. 1).
In systems with multiple devices (interphones or
monitors) with star connections. Move the jumpers of
all devices to the position BC (Fig. 2).
If the image on the monitor is distorted, move the
jumper to one of the alternative positions from the
Fig. 1
initial one (BC or CD), to eliminate distortion.
EN