paasche TG TALON Guia De Inicio Rapido

paasche TG TALON Guia De Inicio Rapido

Aerógrafos

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

TG TALON – Airbrush
Double Action - Internal Mix - Gravity Feed -
PTFE Packings.
TG Specifications:
• Dual Action • Gravity Feed • Internal Mox • Cutaway Handle w/ Pre-set Needle Stop • PTFE Packing
Options for Talon:
.25mm head (TT-1, TN-1 and TA-1) - Great for jobs requiring the extremely fine detail
.66mm head (TT-3, TN-3 and TA-3) - Great for spraying Metallics, Pearlescent and Thicker Paints
.66mm Fan Aircap (TAF-3, TN-3 and TT-3) Will give a 2-1/2 to 3 inch flat pattern
Working Pressures:
• Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.
• 20-30 PSI is best for detail spraying w/ properly thinned paint
• Use the higher pressures for thicker material where fine detail is not critical or thin the paint to allow
lower pressures.
Equipment Set-up:
The Airbrush is held in the same manner as a pen, with index finger comfortably over the finger button.
1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 20 -55 PSI.
Airbrush Operation:
1. Press down on Finger Button to release air and pull back on button to control quantity of color.
2. To spray a fine line without heavy ends, start moving the airbrush without release of color. Then start
the color at the beginning of line and stop the color at the end, but continue the motion of the airbrush
after the color has stopped.
3. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at
the beginning or end of your strokes.
4. Speed of movement controls density of color and fading effects at beginning and end of strokes.
5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on
the Finger Button to release a small amount of paint.
6. For background work and broad effects, hold the airbrush away from the work surface and pull back
on Finger Button to release required amount of color.
7. For Stippling remove the aircap, push down on the trigger and pump the trigger forward and back.
Adjust the air pressure between 15 and 50 PSI for desired stipple effect.
*Note: Etch lines on Items 2.,3.
and 24. indicate size.
All should match when installed
on airbrush.
NO. PART
1.
TAL-23
1a.
TAF-3
*2.
TA-1,TA-2,TA-3 Aircap (.25mm, .38mm, .66mm)
*3.
TT-1,TT-2,TT-3 Tip (.25mm, .38mm, .66mm)
4.
MIL-12
5.
TG-30
6.
TG-4
7.
TAL-8
8.
TAL-37
9.
TAL-14
10.
TAL-36
DESCRIPTION
Crown Cap
Fan Aircap for .66mm head -
"O" Ring for TG-30 Shell
Shell Assembly
Cup Cover
Packing Assembly PTFE
Trigger
Valve Casing
Valve Plunger (Includes O-ring)
INSTRUCTIONS AND PARTS LIST TG-TALON
WARNING: Spray materials may be harmful if
inhaled or allowed to come into contact with the
skin or eyes. Consult the product label and material
safety data sheet supplied for the spray material.
Follow all safety precautions. CAUTION:
Ventilated Area Required to remove fumes, dust or
overspray. Maximum Air Pressure 75 P.S.I.
11. TAL-15
12. A-22
17. TAL-18
18.
MIL-11
19.
TAL-17
20.
TAL-19
21.
MIL-12
22.
TAL-34
23.
3A-4
*24. TN-1,TN-2,TN-3 Needle (.25mm, .38mm, .66mm)
25.
TAL-35
26.
TAL-28
Valve Adapter (Includes O-ring)
Spring
Rocker Assembly
Needle Spring
Spring Housing
Needle Lock Nut
"O" Ring for TG-34 Handle
Handle & Stop Assembly
"O" Ring
Allen Wrench
Wrench
Well

Publicidad

Tabla de contenido
loading

Resumen de contenidos para paasche TG TALON

  • Página 1 WARNING: Spray materials may be harmful if inhaled or allowed to come into contact with the skin or eyes. Consult the product label and material TG TALON – Airbrush safety data sheet supplied for the spray material. Follow all safety precautions. CAUTION:...
  • Página 2: Personal Settings

    2. Paint leaking to trigger area - remove guts of airbrush and slightly tighten packing or replace if needed 3. Lubricate needle and trigger - apply Paasche Airbrush Lube (AL-2) to needle shaft and trigger slot area...
  • Página 3 Maximaler Luftdruck 75 P.S.I. - PTFE Dichtung EINFÜHRUNG: Der Paasche® TALON Airbrush ermöglicht das Zeichnen feiner Details und Schattierungen mit Zerstäubungsflüssigkeiten, die Schwerkraftzufuhr erfordern. Die doppelt wirkende Funktion mit interner Mischung bietet Flexibilität beim Einstellen von Farbe und Luft ohne Arbeitsunterbrechung. PTFE Stopfbuchsen.
  • Página 4 Kraft zu erhöhen oder zu verringern. 2. Farblecks im Tasthebelbereich - innere Teile des Airbrush ausbauen und Stopfbuchse leicht festziehen oder austauschen. 3. Nadel und Tasthebel schmieren - Paasche Airbrush Lube (AL-2) auf den Nadelschaft und den Tasthebel- Schlitzbereich auftragen.
  • Página 5 - joints en PTFE. ou surpulvérisation. Pression maximale aérien 75 INTRODUCTlON: Les principales caractéristiques de l’aérographe Paasche® ‘TG’ TALON incluent la capacité de pulvériser des liquides exigeant une alimentation par gravité pour rendre les fins détails et les ouvrages d’estompage.
  • Página 6: Remplacement De La Buse

    2. Fuites de peinture vers la zone de gâchette - retirer les rouages de l’aérographe et serrer légèrement le joint ou remplacer si besoin est. 3. Lubrifier l’aiguille et la gâchette - appliquer Paasche Airbrush Lube/Lubrifiant pour aérographe (AL-2) sur l’axe de l’aiguille et la zone de la fente de gâchette.
  • Página 7: Instalación Del Equipo

    Consulte la etiqueta del producto y la hoja de datos de seguridad de materiales que TG TALON – Aerógrafos se proporciona para el material de pulverización. Siga todas las precauciones de seguridad. PRECAUCIÓN: Se Doble acción - Mezcla interna - De alimentación...
  • Página 8: Limpieza Del Aerógrafo

    2. Hay fugas de pintura hacia el área del gatillo - retire las piezas internas del aerógrafo y apriete suavemente la empaquetadura o reemplácela si fuese necesario. 3. Lubrique la aguja y el gatillo - aplique el lubricante para aerógrafos Airbrush Lube (AL-2) de Paasche al área del eje de la aguja y a la ranura del gatillo.

Tabla de contenido