Publicidad
Idiomas disponibles
Idiomas disponibles
STEP 4: Plumb vent. Plumb vent using 2" threaded pipe to fitting in basin cover.
Use pipe joint compound on threads and hand tighten only on plastic fittings.
The basin must be vented in accordance with state and local codes. The vent
is essential for proper switch operation and must not be omitted or restricted.
CAUTION: Do not use a mechanical vent with this product. A mechanical vent
will cause improper operation of the automatic switch.
STEP 5: Test unit. Connect power cord to electrical supply as stated under
"Electrical Connections." Secure power cord to piping with ties or tape. Fill unit
with water through inlet. Pump should turn on with 7"–10" of water in tank, and
turn off when 2"–5" of water is left in tank.
MAINTENANCE
Maintenance operations consist of cleaning basin and limited pump mainte-
nance. WARNING: Before any maintenance is performed, shut off water inlet
and disconnect power cord from electrical supply outlet. Pump may become
hot in operation. Allow pump to cool before servicing.
BASIN: Sediment may build up in basin causing pump to operate improperly.
Remove (10) 1/4-20 screws from cover. Remove cord grommet and loosen cords
to allow slack and then remove cover.
Remove pump and clean basin using a mild detergent and water. Reassemble
in reverse order.
Torque screws 18-20 in.-lbs.
PUMP: Sediment or lint can clog pump and cause improper operation. If neces-
sary, remove pump from basin and remove the screws that hold the base plate
and screen to motor housing. Remove baseplate and screen and clean impeller
Figure 3
*Items Not Included with WRS-9EN Basin Kit
*Articles Non Inclus avec Kit de Bassin WRS-9EN
*Los Articulos No Incluyeron con Juego de Palangana WRS-9EN
Incluye un adaptador liso
Un adaptateur à glissement
de 2" x 1-1/2" MNPT
de 2" x 1-1/2" MNPT
por si es requerido
est fourni
1-1/2 po Tuyau de refoulement
Basin Cover • Bassin Couvercle • Cubeta Unión
Tuyau de refoulement
Tubería de descarga
15.68"
On Level 7"-10" • Marche: 7"-10"
Off Level 2"-5" • Arrêt 2"-5"
Figure 4
1.50 ± .25
Cut Dimension
1.25
2
TYPICAL INSTALLATION • INSTALLATION TYPIQUE • INSTALACION TÍPICA
Check valve
Clapet anti-retour
Válvula de Retención
Discharge pipe
Tuyau de refoulement
Tubería de descarga
*Union
*Raccord
*Unión
2" slip x 1-1/2" MNPT
adapter provided.
Use if required.
1-1/2" Discharge pipe
1-1/2" Tubería de descarga
Basin
Bassin
Cubeta
Discharge pipe
10.63"
• En el Nivel 7"-10"
14.50"
• Del Nivel 2"-5"
Rubber Grommet
Passe-Fils en Caoutchouc
Arandelas Aislantes de Caucho
Remove Stem Material
Enlever le MatÈriel de Tige
Quite el Tallo la Materia
and volute passage. Do not use strong solvent on impeller. Clean using a mild
detergent and water and reinstall. See pump manual for other information. For
any other pump repair, return the pump to a Little Giant authorized service center.
FOR TROUBLESHOOTING INFORMATION, SEE PUMP OWNERS MANUAL
INCLUDED WITH WRS-9EN BASIN KIT.
Instructions for replacement of RVMS Pump Switch (C/N 599261)
STEP 1: CAUTION – make certain that the unit is disconnected from the power
source before attempting to service or rework any components.
STEP 2: Disconnect unit from inlet pipe, vent pipe, and discharge pipe.
STEP 3: Remove the 14 machine screws (Figure 2, Item #8) from around the
basin cover.
STEP 4: Take off basin cover and remove cord grommet (Figure 2, Item #1).
STEP 5: Remove RVMS Pump Switch cord from the cord grommet.
STEP 6: Loosen the stainless steel clamp that attaches the RVMS Pump Switch
to the discharge pipe (Figure 2, Item #4).
STEP 7: Slide the RVMS Pump Switch up and off the discharge pipe. Be careful
to note the switch's orientation for re-assembly.
STEP 8: Trim 1.25" from the replacement RVMS Pump Switch stem, as is
detailed in Figure 4. Orientate the rubber grommet approximately 1.5" from the
newly cut bottom of the switch stem.
STEP 9: Clean out the basin to ensure maximum product performance.
Replace the RVMS Pump Switch in the reverse order in which it was removed.
Power Cord Piggyback Plug
Cordon d'Alimentation avec
Prise Mixte
Cable Eléctrico con Enchufe
Incorporado
*2" vent pipe
*2" tuyau de ventilation
*2 tubo de ventilación
1-1/2" slip x 2" MNPT
adapter is provided if a
1-1/2" vent is required.
Au cas d'un event de 1-1/2",
un adaptateur a glissement
de 1-1/2" x 2" MNPT est fourni.
Incluye un adaptador liso
de 1-1/2" x 2" MNPT
para ventilación de 1-1/2".
Inlet of Basin is 1-1/2" FNPT
L'Arrivée de Cuvette est 1-1/2" FNPT
Entrada de Palangana es 1-1/2" FNPT
2" slip X 1-1/2" MNPT
adapter provided.
Use if required.
Un adaptateur à glissement
de 2" x 1-1/2" MNPT
est fourni
Incluye un adaptador liso
de 2" x 1-1/2" MNPT
por si es requerido
*2" Union
*2 po Raccord
*2" Unión
Cover O-Ring
*Intake
Couvercle avec joints toriques
*Prise
Cubierta O-Ring
*Toma
Pump
La Pompe
La Bomba
SPECIFICATIONS • CARACTERISTIQUES • ESPECIFICACIONES
Model No.
Item No.
Volts
Hertz
Amps
N° du
Modèle
Article
Voltage
Hertz
Ampères
Numero de
Articulo
Voltios
Hertzios
Amperios
Modelo
509268
WRS-9EN
115
60
14.75"
*Items Not Included with WRS-9EN Basin Kit
*Articles Non Inclus avec Kit de Bassin WRS-9EN
*Los Articulos No Incluyeron con Juego de Palangana WRS-9EN
Gallons Per Min. (GPM) @ Ht.
Watts
Gallons/Min. (GPM) @ Hauteur
Watts
Galones Por Minuto @ Altura
Vatios
5'
10'
15'
20'
25'
9.0
920
80
70
60
45
25
Shutoff (Ft.)
Max. PSI
Tête d'arrêt
(Pieds)
Max. PSI
cabeza de
Máx. PSI
cierre (Pies)
32
14.1
Publicidad
