Product Familiarisation - Silverline 126499 Manual De Instrucciones

126499
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of dust collection can reduce dust-related hazards.
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
WARNING: Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as that
specified on the nameplate of the tool. A power source with a voltage greater than
that specified for the tool can result in serious injury to the user, and damage to the
tool. If in doubt, do not plug in the tool. Using a power source with a voltage less
than the nameplate rating is harmful to the motor.
Spray Gun Safety
• Never point a spray gun towards yourself, other people, or animals
• Always read paint or stain manufacturer's guidance thoroughly. If paint or stain
comes into contact with skin, consult manufacturer's guidance immediately
• This spray gun works at very high pressure, and is capable of penetrating skin.
If paint or stain is injected under a person's skin, seek medical help immediately
• Never use this spray gun with flammable, corrosive, toxic, or abrasive liquids
• Always spray in a well-ventilated area, away from any sources of ignition. Be
aware that even very light wind will cause the paint or stain mist to drift
• Ensure other people, especially children, are kept well away from the work area
• WARNING: Solvents and paints are harmful and can even be toxic. Some
solvents and paints are extremely flammable. Handle with care, according to
the manufacturer's recommendations. Store solvents and paint in sealed, leak
proof containers made of a material that is chemically resistant to the specific
solvent. Always wear suitable protective equipment and dispose of solvents
and paints, as well as contaminated items, as special waste, according to laws
and regulations.
• WARNING: When spraying coating materials, dangerous vapours or aerosols,
which are detrimental to your health, are produced. Please read all labels
and safety instructions carefully, and observe all indicated instructions and
recommendations. In case of doubt, please ask the material supplier. Use
respiratory protection when spraying. The respiratory equipment used must
be suitable for the material in use and adapted to the degree of the vapour
concentration. When spraying paint, use respiratory equipment independent of
the ambient atmosphere, or equipment with filter combination A1/A2-P2. Ensure
a sufficient protection of your skin during all spraying and cleaning procedures.
Wear appropriate protective clothes and use suitable protective skin ointments.
• WARNING: DO NOT spray acids, caustic solutions, removers and similar
substances.

Product Familiarisation

1
Nozzle
2 Nozzle Guard
3 Regulator Knob
4 Trigger Switch
5 Fluid Container
6 Cleaning Pin
7 Viscosity Cup
8 Nozzle Extension
9 Spare Nozzle
www.silverlinetools.com
120W Spray Gun
5