Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Silverline 263354 Manual De Instrucciones

GB

Product Familiarisation

1 Pump Unit
2 Roller Frame Handle
3 Extension Connector
4 Extension
5 Extension Threaded Collar
6 Paint Roller
7 Paint Filter
8 Short Suction Hose
9
Long Pressure Hose
10 Pump Unit Handle
11 On/Off Switch (rear of unit)
12 Paint Control Switch
13 Pressure Hose Securing Collar
14 Pressure Hose Nozzle
15 Suction Hose Securing Collar
16 Suction Hose Nozzle
17 Front Cover Clips
18 Front Cover
19 Valve Seal
20 Paint Filter
21 Flow Rotary Control
22 Roller Frame Handle
23 Release Lever
24 Stop Button
25 Suction Hose Nozzle
26 Pressure Hose Nozzle
27 Paint Control Switch
28 Paint Short Hose
29 Screw Holes (x 6)
30 Paint Short Hose Nozzle

Intended Use

• Portable mains-operated pump system for pumping paint to a paint roller
for convenience and an increased work rate. This device is intended for
domestic use. It is not suitable for commercial, industrial or rental use.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with
all its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before
attaching or changing any accessories, or making any adjustments.
6 6
IMPORTANT: Do not use solvent (oil)-based paints or textured paints with
this paint system. It is only suitable for emulsion (water or latex- based)
paints. Paint that requires brushes to be washed in solvents, white spirit or
similar, is not suitable for this product.
IMPORTANT: Always refer to the instructions provided with the paint in
addition to the instructions provided in this manual, as they may include
vital safety points, correct or maximum thinning ratio, and required surface
treatment before painting.
Assembly
1. Partly unscrew the Pressure Hose Securing Collar (13) and insert one
end of the Long Pressure Hose (9) over the Pressure Hose Nozzle (26),
making sure it is fully inserted. Tighten the Pressure Hose Securing
Collar. Partly unscrew the securing collar at the base of Roller Frame
Handle (2) and insert the other end of the Long Pressure Hose over
the nozzle, again making sure it is fully inserted before tightening the
securing collar
2. Depending on required length between the Roller Frame Handle and
the Paint Roller (6), fit one or two Extensions (4); or for a short length
fit the Paint Roller directly to the Roller Frame Handle. Whichever part
you wish to remove or add, the procedure is the same. Unscrew the
collar, for example the Extension Threaded Collar (5), and separate by
pulling the two parts apart. To join two parts insert the connector, for
example Extension Connector (3), into the receiving socket of the other
extension and secure by tightening the Extension Threaded Collar (5).
Do not over-tighten the Collars as this could make removal difficult
3. Fit the Paint Roller (6) to the Roller Frame Handle (2)
4. Connect the open end of the Short Suction Hose (8) to the Suction
Hose Nozzle (16) after first partially unscrewing the Suction Hose
Securing Collar (15) and then re-tightening after the hose has been
fully inserted
Preparing for use
1. Prepare the work area, using plastic sheeting and tape, to protect from
paint spills or drips
2. Prepare the surface area ready for painting
3. Prepare the paint as per the manufacturer's instructions - stirring and
possibly diluting. Use a paint stirrer that is long enough to reach the
very bottom of the paint container
4. Position the paint system and paint pot in a secure position during use,
to avoid the risk of the paint being knocked or tipped
5. Submerge the Paint Filter (20) fully in the paint. Set the plastic stop on
the Short Suction Hose (8) to the required position so the Paint Filter
is at the right depth
IMPORTANT: For the initial draw of paint into the system, keep the unit and
the paint at the same level until both tubes are full of paint and the system
is correctly primed. The system is now ready to use and the main body can
be moved around where necessary. Make sure that the fill tube remains
fully submerged at the bottom of the paint container at all times. Failure
to do so will result in air being circulated into the system and priming the
system will need to be repeated.
IMPORTANT: Never use the Short Suction Hose without the Paint Filter fitted
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this tool.
Switching on and off
1. Turn the Paint Control Switch (12) to the 'working' position and set
the Flow Rotary Control (21) to the half way position between 'MIN'
and 'MAX'
2. Turn the Pump Unit (1) on using the On/Off Switch (11). The paint
will take approximately 2 minutes to reach the Paint Roller and is
ready to use when the first drops of paint appear. Apply paint to the
surface area. Adjust the Flow Rotary Control to set the correct level
of paint required so an adequate supply of paint is provided without
drips falling from the roller. Over time user technique will improve so
a faster supply of paint can be used but for initial use a low paint feed
rate is recommended