Technical Data; Barrier Installation - DITEC QIK4-7 Manual Para La Instalacion Y La Manutencion

1.

TECHNICAL DATA

Power supply
Motor power supply
Absorption
Torque
Condenser
Opening time
Rod length (max)
Service class
Intermittence
Temperature
Degree of protection
Control panel
2. REFERENCE TO ILLUSTRATIONS
The given operating and performance features can only be
guaranteed with the use of DITEC accessories and safety
devices.
2.1 Standard installation references (fig. 1)
[1] Radio
[2] Flashing light
[3] Key selector switch
[4] Connect the power supply to an approved omnipolar switch
with an opening distance of the contacts of at least 3 mm
(not supplied).
The connection to the mains must be made via an indepen-
dent channel, separated from the connections to command
and safety devices.
[5] Photocells
[6] Barrier cabinet
[7] Barrier rod
[8] Barrier support
2.2 Barrier references (fig. 3-4)
[9] Fastening base
[10] Key release
[11] Motor
[12] End stop
[13] End stop sliding block
[14] Mechanical stop regulation
[15] Spring
[16] Control panel
[17] Mechanical stop
2.3 Accessories
QIKB27 Rod 2700 mm
QIKB37 Rod 3700 mm
QIKB50 Rod 5000 mm
QIKB60 Rod 6000 mm
QIKM1 Grey spring
QIKM2 Green spring
QIKM3 Red spring Ø38 mm
QIKM4 Red spring Ø51 mm
QIKZ
Fastening base
QIKAF Fixed support
QIKAFZ Fixed support fastening base
QIKAFE Fixed support with electromagnetic block
QIKAM Mobile support
QIKGR Aluminium barrier 2000 mm
QIKSN Articulation for rod
QIK4E
230 V~ / 50 Hz
230 V~
1,2 A
90 Nm
8 µF
4 s/90°
3700 mm
4 - INTENSE
S2 = 15 min, S3 = 30%
-20° C / +55° C
IP24D
E1A
QIKBG
QIKBAT Battery kit
QIKLUX Light kit
XELCQ
QIKC
3.
Unless otherwise specified, all measurements are expressed
in millimetres (mm).
To open the cabinet:
-
-
3.1 Choice of balancing spring
Choose the balancing spring as indicated in the tables on page 5.
Attention: for L≥4000 mm, it is necessary to use the fixed support
QIKAF, or the mobile support QIKAM.

3.2 Barrier installation

-
-
-
-
3.3 Choice of opening direction and rod installation
-
-
-
11
230 V~ / 50-60 Hz
24V= with encoder
5 - HIGHLY INTENSE
S2 = 60 min, S3 = 60%
-20° C / +55° C
Joint for rod
Photocell container
10 reflectors box
INSTALLATION
release the automation as indicated in the "OPERATING
INSTRUCTIONS".
unscrew the four front screws.
If the flooring does not permit a firm, stable fastening,
prepare a cemented area with the anchoring clamps and
the base plate englobed in the cement. The base plate
must be level and clean.
Insert pieces of iron (or another material) in the holes of
the anchoring clamps, to hook the clamps to the cement
reinforcement as indicated in fig. 3.
Pass the cable guard trunking through the central hole of
the plate.
Attention: check the robustness and stability of the fastening.
Fix the cabinet.
Choose the opening direction as indicated in fig. 5.
Install the rod as indicated in fig. 6.
Set the DIP2 on the control panel as indicated in fig. 5.
QIK7EH
1 A
70 Nm
/
2÷6 s/90°
6000 mm
IP24D
73RQ
QIK4-7 - IP1861
GB