VTech CS6120-2 Guia De Inicio Rapido

Quick start guide
CS6120-2/CS6124
Introduction
This quick start guide provides you with the basic installation
instructions. A limited set of features are described in
abbreviated form.
Please refer to the online user's manual for complete installation
and operation instructions.
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone wall jack
Electrical outlet
(not controlled by
A DSL filter
a wall switch)
(not included)
is required if
Telephone base
you have DSL
power adapter
high-speed
Internet service
Telephone
line cord
Telephone base
Use only the power adapters and batteries supplied with
this product.
Battery installation and charging
Install the battery as shown below. Once you have installed the
battery, you may be able to make and receive short calls. For best
performance, charge the handset battery continuously for at least
16 hours.
1 Plug the battery connector
securely into the socket.
3 Slide the battery
compartment cover towards
the center of the handset
until it clicks into place.
Charger
adapter
Charger enter the handset menu
1. Press MeNU when the phone is not in use.
CID or
2. Press
feature menu.
3. Press SeLeCT to enter that menu.
• To return to the previous menu, press CaNCeL.
• To return to idle mode, press and hold CaNCeL.
Set date and time
1. Press MeNU when the handset is not in use.
2. Scroll to Settings then press SeLeCT.
3. Scroll to Set date/time then press SeLeCT.
4. Use the dialing keys (0-9) to enter the current month, date and
year. Then press SeLeCT.
5. Use the dialing keys (0-9) to enter the hour and minute. Then
press CID or
Press SeLeCT to save.
6.
2 Place the battery with the
wires inside the battery
compartment.
4 Charge the handset in the
telephone base or charger.
Charge light
remains on
when charging.
until the screen displays the desired
to select aM or PM.
Set number of rings
You can set the answering system to answer an incoming call
after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver,
the answering system answers a call after 2 rings when you
have new messages, or after 4 rings when you have no
new messages.
1. Press MeNU when the handset is not in use.
Scroll to answering sys then press SeLeCT.
2.
Scroll to ans sys setup then press SeLeCT.
3.
Scroll to # of rings then press SeLeCT.
4.
CID or to choose 6, 5, 4, 3, 2 or Toll saver and
5. Press
then press SeLeCT to save.
record your own announcement
You can use the preset announcement to answer calls, or replace it
with your own recorded announcement. The announcement can be
up to 90 seconds in length.
1. Press MeNU when the handset is not in use.
2. Scroll to answering Sys then press SeLeCT twice.
3. Press 7 to record.
4. After the handset announces, "Record after the tone. Press 5
when you are done," speak towards the handset microphone.
5. Press 5 when done.
6. Press 2 to play the recorded announcement; or 7 to record
again if desired. Press 3 to delete the recorded announcement.
Press 5 to stop the playback at any time.
IMPOrTaNT!
Refer to the online user's manual for a full set of installation and
operation instructions. For manual download or customer service,
visit our website at www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to www.vtechcanada.com
or call 1 (800) 267-7377.
Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
96-007701-050-100