Bellelli Giotto Instrucciones De Uso página 12

J. metal yoke
K. padding fixture plate
L. metal clip
EN
Initial adjustment of the child seat
Check and if necessary adjust the height of the
harness straps and headrest before fitting the
child seat in a car.
How to check the height of the harness
straps and headrest
Put the child seat on the floor and sit the child
snugly in position.
Check that the straps (I) are adjusted to the
closest position to the child's shoulders and
preferably positioned just above the child's
shoulders (fig. 3).
Adjust the height of the headrest (A) so that the
child's head is well enclosed; the headrest must
not touch the child's shoulders (fig. 4).
How to move the child seat harness straps
Release the harness strap (I) from the metal
yoke (J) behind the backrest of the child seat
(fig. 5).
Unthread the strap from the backrest (fig. 6).
Unthread the padding fixture plate (K) from the
backrest (fig. 7).
Thread both the padding fixture plate (K) and
the strap (I) into the slot in the backrest at the
required height (fig. 8).
Reattach the strap (I) to the metal yoke (J) (fig. 9).
Repeat the same procedure with the other
strap.
Warning: check that the straps (I) pass through
the padding and that the spongy part is facing
towards the child's body.
Warning: check that the straps are not twisted
and that the padding fixture plate (K) cannot slip
through the backrest.
How to adjust the height of the headrest
To raise the headrest (A), pull it up, or push it
down to lower it. A click indicates transition from
one position to the next (fig. 10).
Warning: The correct positioning of the headrest
is essential for the child's safety. Do not remove
the headrest.
Use of the child seat
Position the child seat on one of the vehicle's
rear seats or on the front passenger seat.
Warning: Regulations in certain countries do not
allow child seats to be installed on vehicle front
seats. Check the law in your country before
proceeding.
Warning: Do not use the child seat on the front
passenger seat if the vehicle is equipped with
an active passenger side airbag.
Warning: Do not fit the child seat on a seat that
only has a lap belt.
Warning: Do not put anything between the child
seat and the car seat.
Group 1 (from 9 to 18 kg)
Position the child seat on the seat of the vehicle so
that it is fully supported on the seat and backrest.
Warning: The car seat belt routing positions are
marked in red. Do not route the car seat belt in
positions other than those indicated.
Pass the diagonal section of the car seat belt
across the upper part of the backrest (fig. 11).
Pass the lap section of the car seat belt under
the armrest of the child seat.
Pass both straps through the openings in the
child seat backrest.
Pass both of them under the armrest of the child
seat.
Close the car seat belt.
Tension the car seat belt well, check that there
are no twists and that it runs smoothly under the
armrests of the child seat.
How to remove the child seat
Release the car seat belt, unthread it from the
child seat and allow it to retract.
How to position the child in the seat
Press adjuster (E) and simultaneously pull both
the harness straps (I) of the child seat (fig. 12).
Press the red buckle button (G) to open it (fig. 13).
Open the straps (I), laying them on the sides of
the child seat (fig. 14).
Sit the child in the child seat.
Bring the two harness tongues together and
insert them into the buckle (G). A click indicates
when the buckle is closed correctly (fig. 15).
Position the padding sections (H) on the
shoulders and chest of the child, pulling them
downwards.
Pull the adjuster strap (F) to tighten the safety
harness snugly over the child (fig. 16).
Warning: During the journey periodically check
that the child has not freed itself from the child
seat.
10