Instructions For Assembly - Kettler CHAMP 5.0 Instrucciones De Montaje

Assembly Instructions
USA
Before assembling or using the table-tennis table, please read the following instructions carefully. They contain important
information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a
safe place for maintenance purposes or for ordering spare parts.
All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control
during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our
customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you have
any cause for complaint, please contact your KETTLER dealer.
Note on Safety
■ The table-tennis table should be used only for its intended pur-
pose, i.e. for playing with suitable table-tennis bats and balls.
■
All other uses are prohibited and may be dangerous. The man-
ufacturer cannot be held liable for damage or injury caused by
improper use of the table.
■ Damaged or worn components may endanger your safety or
shorten the lifespan of the table-tennis table. Replace worn or
damaged components immediately and remove the table from
use until this has been done. Use only spare parts manufactured
by KETTLER.
■ The table-tennis table complies with all safety regulations. Incor-
rect repairs, alterations to the design (removal of original parts,
addition of other components etc.) may endanger the safety of
the user.
■ Instruct other persons (in particular children) using the table in its
Handling the equipment
■ Do not use the table-tennis table until it has been fully and cor-
rectly assembled and checked.
■
Ensure that table-tennis tables which are not weatherproof are
not exposed to dampness or rain. Keep them well away from di-
rect sources of heat. Should the surface become warped, lay the
table on a level surface for a few days.
■ Set the table up on a level surface.
■
Do not cover it with plastic foil, under which condensation may
form. We recommend the weatherproof KETTLER tarpaulin, art.
no. 7032-300.
■ For practising without a partner, the table halves can be folded
up singly.
■
For more information on the sport of table-tennis, you are referred
to the specialist literature on the subject.

Instructions for Assembly

■ The equipment must be assembled with due care by two adult
persons.
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
■ Ensure that your working area is free of possible sources of dan-
ger, for example don't leave any tools lying around. Always dis-
pose packaging material in such a way that it may not cause
any danger. There is always a risk of suffocation if children play
with plastic bags!
■ Caution: While assembly of the product keep off children's reach
2
correct use, and draw their attention to any potential source of
danger, especially when setting up or dismantling the table.
■ Caution: While assembly of the product keep off children's reach
(Choking hazard - contains small parts).
■ When setting up or dismantling the table, stay clear of its folding
radius.
■ When folded up, the table-tennis table presents a large surface
to the wind. For this reason, ensure that it is stored in a sheltered
position.
■ The table-tennis table may be pushed only into the transport po-
sition because there is otherwise a danger of injury.
■ The unit complies with the standard EN 14468–1:2004.
■ Depending on frequency of use, check all screws, bolts etc. reg-
ularly to ensure that they are in good condition.
■ In case of enquiry, please contact your KETTLER dealer.
■ Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the environ-
ment. In most cases, a slightly dampened cloth is sufficient.
■ Waste Disposal: KETTLER products are recyclable. At the end of
its useful life please dispose of this article correctly and safely
(local refuse sites).
(Choking hazard - contains small parts).
■ The fastening material required for each assembly step is shown in
the diagram inset. Use the fastening material exactly as instructed.
■ Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand until
resistance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that all
screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly
(the locking device is destroyed), and must be replaced.
■ For technical reasons, we reserve the right to carry out prelimi-
nary assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary. Goods may only be retur-
ned after prior arrangement and in (internal) packaging, which is
safe for transportation, in the original box if possible. It is important
to provide a detailed defect description / damage report!