Bayco SL-260 Instrucciones De Instalación

INS-260-12
Installation Instructions for
Model SL-260 Work Light Replacement
WARNING: RISK OF ELECTRICAL SHOCK
Unplug the light before replacing the light
Electrical Rating - All models use 125 Volts 60 Hz
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL PLUG
WHEN REPLACING THE LED LIGHT HANDLE
CAUTION
DO NOT use this cord reel in explosive atmospheres, near flammable liquids, or where
explosion proof lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the hand lamp
DO NOT immerse in water
DO NOT use in areas where water can accumulate or in rain or mist
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only
GENERAL USE CORD REEL ONLY. NOT FOR HARD USE. FOR INDOOR DRY
LOCATION USE ONLY FOR LIGHT DUTY RESIDENTIAL USE ONLY
WARNING: NOT FOR USE ABOVE HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
IMPORTANT SAFETY INSTRUCTIONS
This product has a 3 prong polarized plug on the power cord. Do not attempt to bypass
this safety feature by removing the round plug and defeat his safety feature. This plug will
fit into a grounded outlet only one way. If the plug does not fit fully into the outlet, contact
a qualified electrician. Never use with a two wire extension cord.
Thank you for purchasing this Bayco work light. Save these instructions.
Please read these instructions before using your work light.
OPERATION
To operate, plug into a 120 Volt 60 HZ outlet. The work light has a two position rocker
switch to activate the floodlight: or turn it off.
SAFETY
CAUTION BRIGHT LED RADIATION: AVOID DIRECT EYE EXPOSURE. The light is a
Class 2 LED product per IEC 60825-1 Edition 1.2.2001.
PRE- ASSEMBLY INFORMATION
Tools Required
Wire cutter pliers
Wire Stripper
Electrical connector crimping tool
The SL-260 replacement work light comes with the following items
Two U-shaped metal crimp rings
Two electrical crimp connectors
Installation instructions
Lineman's pliers
Small Philips screwdriver
Flexible strain relief
One magnetic hook
BAYCO • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • www.baycoproducts.com
If you are missing any of the above materials, contact Bayco at 800-233-2155 to obtain
the missing item(s).
Crimp connectors
Connecteurs à sertir
Conectores
WORK LIGHT REPLACEMENT
The SL-260 is a replacement LED work light handle assembly.
Unplug the light before replacing the light
Prepare the existing cord
1. Cut the existing work light off of the cord reel cord.
2. Slip the black strain relief over the cord with the wide end facing the end of the wires.
Slide it a few inches away from the end of the cord.
3. Strip the white and black wires per the drawing. Position the 2 U-shaped clamp rings
per the drawing and crimp them tightly with the lineman's pliers. The clip should be
tight enough so that it cannot be moved along the cord.
Attaching the cord to the handle
a. Open the handle by removing 4 screws. Set these aside. Carefully separate the
handle halves starting at the switch end. Place the empty handle half on the side.
Remove the plastic cord clamp.
b. Take the white wire from the work light circuit and the white wire from the cord and
twist their copper conductors together. Then, take the electrical crimp connector and
slide it over the twisted conductors as far as it will go. Hold this assembly while
crimping the connector with an electrical crimping tool. Repeat
this step with the black wires. Test for a secure crimp.
c. Slide the strain relief up to the base of the light and lay the
strain relief into the end of the light. The strain relief only fits
properly when the square sides of the strain relief fit easily into
the base of the light.
d. Locate the #2 U-shape clamp ring inside the plastic cord clamp
location. Attach the plastic cord clamp with 2 screws.
e. With the cord and wires tucked into the light housing, replace
the handle half and secure with 4 screws from step a)
U-rings Strain-relief
U-anneaux Décharge de traction
U-anillos De alivio de tensión