General Safety Rules - Hilti TE 76 / TE 76 P Manual De Instrucciones

General safety rules

Warning! Read and understand all instructions. Failure
to follow all instructions listed below, may result in elec-
tric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1. Work area
Keep your work area clean and well lit. Cluttered bench-
es and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
Grounded tools must be plugged into an outlet proper-
ly installed and grounded in accordance with all codes
and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adaptor
plugs. Check with a qualified electrician if you are in
doubt as to whether the outlet is properly grounded. If
the tools should electrically malfunction or break down,
grounding provides a low resistance path to carry elec-
tricity away from the user.
Applicable only to Class I (grounded) tools.
Double Insulated tools are equipped with a polarized
plug (one blade is wider than the other.) This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install a polar-
ized outlet. Do not change the plug in any way. Double
Insulation Z eliminates the need for the three wire ground-
ed power cord and grounded power supply system.
Applicable only to Class II tools.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is ground-
ed.
Don't expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
When operating a power tool outside, use an outdoor
extension cord marked "W-A" or "W". These cords are
rated for outdoor use and reduce the risk of electric
shock.
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5071196 / 000 / 00
3. Personal safety
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
Avoid accidental starting. Be sure the switch is off before
plugging in. Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites acci-
dents.
Remove adjusting keys or wrenches before turning the
tool on. A wrench or a key that is left attached to a rotat-
ing part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at
all times. Proper footing and balance enables better con-
trol of the tool in unexpected situations.
Use safety equipment. Always wear eye pro-
tection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used
for appropriate conditions.
4. Tool use and care
Use clamps or other practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may
lead to loss of control.
Do not force tool. Use the correct tool for your applica-
tion. The correct tool will do the job better and safer at
the rate for which it is designed.
Do not use tool if switch does not turn it on or off. Any
tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
Disconnect the plug from the power source before mak-
ing any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained
users.
Maintain tools with care. Keep cutting tools sharp and
clean. Properly maintained tools with sharp cutting edges
are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tools operation. If damaged, have the tool ser-
viced before using. Many accidents are caused by poor-
ly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.