EINHELL EXPERT TE-CC 315 U Manual De Instrucciones Original página 32

Anleitung_TE_CC_315_U_SPK8__ 19.11.12 15:56 Seite 32
GB
you set an angle of approx. 30° (see 6.1.3).
To assemble, proceed in reverse order.
n
When closing the chip box (23) ensure that the
n
control pin (H) slides into the opening provided
for it on the microswitch (I).
5.2.2 Adjusting the splitter (Fig. 24-25/item 17)
Important. Pull out the power plug.
n
Set the saw blade (12) to maximum cutting depth
n
and lock it (see 6.1.2).
Open the chip box (23) (see 5.2.1).
n
Undo the nut (J) using the wrench (30).
n
Pull up the splitter (17) upwards until the gap
n
between the saw table (1) and the upper edge of
the splitter (17) is at its maximum (Fig. 24).
The distance between the splitter (12) and the
n
saw blade (17) may again be max. 8 mm (see
Fig. 24 – 25).
Tighten the nut (J) again and fit the chip box (23)
n
again (see 5.2.1).
5.2.3 Replacing the saw blade (Fig. 26-28/item
12)
Important. Pull out the power plug. Wear
n
protective gloves at all times when handling
saw blades.
Set the saw blade (12) to maximum cutting depth
n
(see 6.1.2).
Open the chip box (23) (see point 5.2.1).
n
Remove the splitter (17) (see point 5.2.2).
n
Place the flange wrench (29) on the saw blade
n
flange (K).
Undo the flange screw (L) turning the wrench (30)
n
towards the saw blade (12) (Fig. 26).
Remove the flange screw (L) and saw blade
n
flange (K) (Fig. 27).
Remove the saw blade (12) from the inner flange
n
and pull it out in an upwards direction (Fig. 28).
Clean the saw blade flange thoroughly before
n
fitting the new saw blade (12).
Fit and fasten the new saw blade (12) in reverse
n
order.
Important. Note the running direction. The
cutting angle of the teeth must point in running
direction, i.e. forwards (see the arrow on the chip
box).
Fit and adjust the splitter (17) (see point 5.2.2).
n
Close the chip box (23) (see point 5.2.1).
n
Refit and set the saw blade guard (18) and the
n
sliding table (15) (see point 5.1.3 – 5.1.4)
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.
5.3 Stops
32
5.3.1 Parallel stop
5.3.1.1 Stop height (Fig. 29 – 33)
The stop rail (2) for the parallel stop (3) has two
n
different guide faces (high and low).
For thick material you must use the stop rail (2) as
n
shown in Fig. 29, for thin material you must use
the stop rail as shown in Fig. 33.
5.3.1.2 Turning the stop rail (Fig. 31-33/Item 2)
First undo the wing nuts (B) to turn the stop rail
n
(2).
The stop rail (2) can now by pulled off the guide
n
rail (E) and can be pushed back over it with the
appropriate guide.
Retighten the wing nuts (B).
n
5.3.1.3 Cutting width (Fig. 29 – 30)
The parallel stop (3) has to be used when making
n
longitudinal cuts in wooden workpieces.
The parallel stop (3) should be mounted on the
n
right-hand side of the saw blade (12).
Place the parallel stop (3) on the guide rail for the
n
parallel stop (5) from above (Fig. 29).
There are 2 scales (C/D) on the guide rail for the
n
parallel stop (5) which show the distance
between the stop rail (2) and the saw blade (12)
(Fig. 30).
Depending on this, choose the appropriate scale
n
to suit whether the stop rail (2) is turned for thick
or thin material:
High stop rail (thick material):
Scale D
Low stop rail (thin material):
Scale C
Set the parallel stop (3) for the required
n
dimension using the inspection window (A) and
secure it using the clamp lever for the parallel
stop (4).
5.3.1.4 Adjusting the stop length (Fig. 29, 34)
The stop rail (2) can be moved in longitudinal
n
direction in order to prevent the workpiece from
becoming jammed.
Rule of thumb: The rear end of the stop comes up
n
against an imaginary line that begins roughly at
the center of the blade and runs at an angle of
45° to the rear.
Set the required cutting width.
n
Slacken the wing nuts (B) and push the stop rail
n
(2) forward until it touches the imaginary 45° line.
Tighten the wing nuts (B) again.
n