Technical Specifications; Maintenance And Care; Schmalz Gmbh - schmalz EVE-TR-T Manual De Instrucciones

4 Technical Specifications

Dimensions 235.1 x 268.5 x
[mm] 160.5
Max. vacuum
-850
[mbar]
Frequency
50
[Hz]
Max. suction capacity
3.9
3
[m /h]
Voltage
220-240
[V]
Current range
1.65
[A]
Power rating
0.18 (50 Hz)
[kW]
Protection class
IP 54
Weight
3
[kg]
Noise level
59
[dB(A)]
Vacuum connection Pneumatic quick-connect
coupling with Nominal diameter
ø= 5 mm

5 Maintenance and Care

Through regular maintenance of your vacuum pump,
your work results will be optimized. Maintenance
intervals depend upon the application and environmental
conditions.
Maintenance of the vacuum pump may only be carried
out by qualified specialist personnel.
Before starting any maintenance work, remove the plug
[10] to avoid accidentally switching the pump back on.
Depending on the degree of contamination, the filter [6]
should be cleaned. To do this, unscrew the filter cover
[3] and blast the filter insert clean with pressurized air.
The rotary vanes are subject to wear caused by abrasion
against the housing. For this reason, the rotary vanes
should be checked at an interval of 3000 hours for
consistency in their dimensions. To do this, unscrew the
housing cover [5] as described and remove the vanes.
The width A of a vane must measure at least 11 mm.
When replacing the vanes clean the housing with dry,
pressurized air.
Caution: The housing cover [5] can become hot during
pump operation. This could result in burns.
235.1 x 268.5 x
160.5
-850
60
4.0
110-120
3.5
0.21 (60 Hz)
IP 54
3
59
3000
Wearing parts set
VST-EVE 4:
10.03.01.00108
The rolling contact bearings included in the Multi-
Clamp vacuum pump have a life-time lubrication and
thus require no maintenance. The bearings may only be
replaced by the manufacturer and only with original
replacement parts.
The filter insert included in the wearing parts set can be
inserted after the housing cover has been removed and
the designated chamber has been cleaned, as described
below.
Caution: The filter insert is not always included in all
variants of the extent of delivery of the Multi-Clamp
vacuum pump. This can however be upgraded at any
time.
A > 11 mm
MIN
Page 2
Wearing parts set
VST-EVE 4:
10.03.01.00108
6 Transport
The Multi-Clamp vacuum pump may only be stored and
transported in dry surroundings. The pump can be
picked up using the designated handle. To further aid
transport a cable drum has been integrated, around
which the power cable can be wound.
7 Accessories and Spare Parts
Type
Wearing parts set VST EVE 4,
consisting of:
5 x rotary vanes
1 x additional paper filter
Outlet valve
LDV-G3/8-AGx25-EVE-4
Filter insert (round)
FILT-EINS 27x23 A2 VF-1/4-Draht
8 Troubleshooting
Problem Cause
 The filter is too dirty (for cleaning
No operating vacuum
even though the pump is
see section 5)
 The rotary vanes are worn and
running
produce no vacuum any more (for
replacing see section 5)
 Blockage in a hose line
 Leakage in system
 Suction of porous materials
 Damaged sealing materials
 The pump has become too hot
Pump suddenly switches
off (lack of ventilation)
 Power outage
 Too much fluid has entered into
the pump
9 Warranty
J. Schmalz GmbH guarantees the devices described in
these operating instructions in accordance with our
general terms of sale and delivery. The same applies to
spare parts, provided that these are original parts
supplied by us. We are not liable for any damage
resulting from the use of non-original spare parts or
accessories. Wearing parts are not covered by the
warranty.
Item number
10.03.01.00108
10.03.01.00110
10.07.01.00013