Description Of Use; Sequence Of Operation - Simon Plug & Drive WALLBOX 2 TOMAS M3T2 Instrucciones De Instalación

ENGLISH

DESCRIPTION OF USE

The Recharge Case solution with 1 Mennekes Outlet + 1 Schuko Outlet (Art.
0600582-039) permits the option to manage the recharge of any type of
electric vehicle in the same case: 4-wheel vehicles such as cars and quadricycles
(quads) and 2-wheel vehicles such as scooters and electric bicycles, using the
suitable connector for each vehicle.
The case offers an ergonomic design which is intuitive and user-friendly which
makes it the ideal solution for any use environment: from private household
and property-owner association uses up to the end client environment such as
a public parking facility, hotel parking garage, shopping centre or any corporate
environment.
By means of the Programmer Mifare RFID Card, the maintenance user can
autonomously carry out the management activity of the recharge infrastructure
and may configure services such as the free/paid recharge, client payment type
(fixed or sporadic) and the duration time of the recharge.
Optionally by means of a Web Page access (Simon Link it), the maintenance user
can remotely monitor the supplied energy and the enabled timetables and/or
the use of the recharge point:
Start Time and End Time.

SEQUENCE OF OPERATION

1) In the initial phase, the recharge case is in a clear operating status (Stand By)
in order to carry out the recharge of electric vehicles in charging mode 3
(Mennekes Blue LED indicator shut off and the RFID Viewer Indicator is fixed
green light).
2) The user must be authenticated in order to use the recharge solution by
placing the card close to the Mifare RFID Reader. If the user is authenticated in
the proper way, the RFID viewer identifier flashes in a green light during 10s
Otherwise, it flashes 10s in red light prior to returning to initial status of Stand
By.
When the solution is payment (prepaid RFID card), the pending balance is
updated in the card itself at the time of authentication.
3) If the authentication is correct, starting from the flashing green light of the
RFID viewer identifier, the user can connect the cable with the plug in the
suitable connector.
Finally, the RFID viewer changes to a fixed blue light after 10s of flashing.
4) In the Charging status (Charging), the RFID viewer indicator becomes a fixed
blue light and the user can manage to use an outlet or the two outlets in a
simultaneous way. The Mennekes Outlet LED indicator remains fixed to indicate
that the electric vehicle is prepared to receive the charge (EV Ready).
If any incident occurs in the vehicle or cable during the charging process, the
Mennekes Outlet LED indicator changes to a fixed red light (Charge Error).
5) The user can halt the charging process at any time by once more identifying
himself/herself with the card in the Mifare RFID reader (Stop Charge). If the
card coincides with the card that initiated the charging process, the recharge is
halted and the Mennekes outlet will be unblocked (if required).
Once the recharge process has halted, the RFID viewer identifier changes to
initial status (Stand By) and the user may remove the cable.
If the user removes the cable without placing the identification card near, the
viewer identifier returns to the initial status when the specified timer for the
recharge concludes.
6) Finally, the charging will conclude (End Charge) when the parameterized
recharge time concludes. The RFID viewer identifier changes to a fixed green
light (Stand By) again and the LED Identifier of the Mennekes outlet (EV Ready)
shuts off.
The description of the functioning sequence provides details of a series of
parameters (Balance, prepaid card, recharge timer, etc.) which can be modified
with the Master RFID Card. The description of the functioning sequence
provides details of a series of parameters (Balance, prepaid card, recharge
timer, etc.) which can be modified with the Master RFID Card.
The card must be modified with the Mifare RFID Cards recorder by the Service
Operator.
In the cards supplied by default by the recharge case, the Balance Discount is 0
Euros and the recharge timer is 8 hr.
To obtain more detailed information, query the Configuration Manual of the
Recharge Case and Recorder.
FEATURES
Number of outlets: 1 Schuko Outlet (UNE 20315-1-2) and 1 Mennekes Outlet
(IEC 62196-2, type 2) (Simultaneous Functioning).
Charging Mode 2 and 3 (according to IEC 62196-2).
Performance: Single Phase 16A and Three-Phase 32A.
Light indicators of the Charging process status in the RFID viewer (Red, Green
and Blue) and the indicator of the Mennekes charging outlet status (Blue and
Red).
User identification by means of the Mifare RF-ID Card (They include 2 Mifare
RFID cards recorded with the configuration by default).
Electrical Connection System and BUS: Internal with protected terminals for
Power and BUS.
Electrical protection (optional):
- Automatic, overload and short circuits
- Differential, direct and indirect contacts
Energy Measurement and Monitoring (optional): Local and Remote RS 485 BUS
integrated with Stored Energy Reading (kWh) and the possibility of external
reset of partial measures.
Outlet Lock: Electronics that prevent the removal of the M3T2 connector plug
when the electronic vehicle is charging. The user must wait to finish charging
or must authenticate with the RFID card to unlock the electronics.
Schedule discrimination (Optional): Inclusion of a Schedule Planner to take
advantage of the Variable Electricity Rates adapted to the use of electronic
vehicles.
CHARGING BOX ELEMENTS
4