Product Familiarisation - Silverline 574483 Manual De Instrucciones

Ocultar thumbs

Contenido

página de 29

/ 29
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

574483

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection

can reduce dust-related hazards

Power Tool Use & Care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed

b) Do not use the power tool if the switch does not turn it on and off. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the risk of starting the power

tool accidentally

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool's

operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could

result in a hazardous situation

Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained

Additional Safety for SDS Drills

• Important: It is imperative to follow all national safety regulations concerning the type of

work being undertaken, operation and maintenance

• Do not allow anyone under the age of 18 years to use this tool, and ensure that

operators are qualified and familiar with the operating and safety instructions

• Masonry drilling or chiselling can create sharp particles that will impact the operator.

Wear impact-resistant safety glasses and protective clothing, including safety boots

• Core drills should only be used with SDS drills featuring a safety clutch to prevent

jamming, which could cause an injury to the operator

• If the safety clutch disengages the drive during use, quickly release the trigger and

remove the core drill or bit from the masonry surface being drilled. Do not continue

operation until the cause of the disengagement is understood

• Do not operate SDS drills whilst up a ladder or in any location where there is a risk of

falling. SDS drills are heavy and produce strong vibration and high torque in use

• Wear suitable protective anti-vibration gloves that are non-fabric or coated fabric

to prevent loose strands of material catching in the rotating drill bit. Discard gloves

immediately if material is visibly frayed

• Drilling can produce large volumes of dust and debris that may be toxic. Wear

respiratory protection suitable for the work being undertaken. A minimum rating of

FFP2 is recommended

• SDS drills produce high volumes of noise and suitable ear protection must be worn at all

times while operating the tool

• SDS drills produce a very high level of vibration when operating in hammer or chisel

mode. Frequent breaks are advised

• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid

touching live components or conductors

• Extension cable reels used with this tool must be completely unwound. Minimum

conductor cross section: 1.25mm2

• Extension reels used outside should be designed for outdoor use and should feature

water-protected sockets and correct cable insulation

• When using an SDS drill outdoors, an RCD device must be used either by connecting to

a socket which incorporates an RCD, or through use of an inline RCD

• Ensure that the chisel or drill bit is securely fixed in the chuck before operating the tool.

Insecure drill bits can be ejected from the machine, causing a hazard

• Ensure lighting is adequate

• Use both hands when operating this tool

• Always use the auxiliary handle supplied with the tool

• Do not place pressure on the tool - to do so could shorten its service life

• Drill bits become hot during operation. Allow to cool prior to handling

• If you are interrupted when operating the drill, complete the process and switch off

before diverting your attention elsewhere

• Always disconnect the SDS drill from the electric supply before changing a chisel or

drill bit

• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired

by a qualified service centre

560W SDS Plus Hammer Drill

• Always wait until the drill has come to a complete stop before placing it down

• On completion of the work, disconnect the tool from the power source and remove the

chisel/bit from the machine

• Periodically check all nuts, bolts and other fixings and tighten where necessary

• Visibly check the tool after use, especially the power cable, which can be damaged by

sharp masonry

• Always fit the dust guard to the bit in use to prevent damage from debris entering the

SDS chuck

• If operating the tool causes discomfort in any way, stop immediately and review your

method of use