Machine Description; Recommended Use; Symbols And Signs - Battipav DYNAMIC 1200 Manual De Instrucciones

Cortadora para obra
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 44
GB
Remove service keys from tool
Form the habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
Avoid unintentional starting
Be sure that the switch is off when plugging in the tool.
Extension cords for outdoor works
When tool is used outdoors, use only extension cords intended for this particular use and so marked.
Stay alert
Watch what you are doing. Use common sense. Do not operate tool when you are inattentive.
Check tool for damaged parts
Before further use of the tool, check it and the safety devices for damages and be sure that they operate properly. Check for
functioning and binding of moving parts, breakage of parts, correct mounting, and any other conditions that may affect the
correct operation of the tool.
Damaged safety devices or other parts should be properly repaired or replaced by an authorised Service Centre unless
otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by an authorised Service Centre.
Do not use tool if its switch cannot be turned on or off.
Warning
For your personal safety use only accessories recommended in this instruction manual or in the relevant catalogues The use
of any other accessory or attachment other than those recommended in this instruction manual or in the relevant catalogue
may present a risk of personal injury.
Have tools repaired by qualified personnel
This electric appliance is in accordance with the safety rules in force. Only qualified experts may carry out repairing of electric
appliances otherwise it may cause considerable danger for the user.
*
1
The noise level emitted by the machine was measured in accordance with the UNI EN12418, EN3744 standards. Measurements
were performed in the absence of load and at maximum speed using a cutting tool with a diameter of 350mm. sector type Art. 967.
*
2
The machine in working conditions has a noise emission higher than 85 dB (A).
The vibration level transmitted to the hand-arm system was measured in accordance with the UNI EN ISO 5349-1 standard
when cutting poroton-type bricks. (L 280 x L 140 x H 100 mm) with cutting tool diameter 350 mm. sector type Art. 967.

MACHINE DESCRIPTION

The DYNAMIC site cutter is a machine intended specifically for cutting bricks, natural stone, granite, concrete items and similar
materials, up to a thickness of 200 mm. The machine uses a wet diamond tipped tool cutting system and is intended for personnel
specialized in the construction sector. The operator works in front of the narrow side of the machine, within reach of the operating
controls, and positions the material to be cut on the moving worktop. He/she starts the machine and moves the cutting head to
bring the tool into contact with the material.

RECOMMENDED USE

CUTTING TOOL: DIAMOND BLADE WET CUTTING
CONTINUOUS CROWN: ceramic, marble, stone, single-fired ceramic LASER/SECTORS: cement, natural stones, granite, abrasive materials
TURBO: cement, natural stones, granite, refractory.
THE TOOL / MATERIAL TO BE CUT MATCHES ARE PURELY INDICATIVE. ALWAYS FOLLOW THE INTENDED USE INDICATIONS
PROVIDED BY THE CUTTING TOOL MANUFACTURER BEFORE ANY APPLICATION.
Admissible working conditions: INTERMITTENT - S6 SERVICE 40%
40%
60%

SYMBOLS AND SIGNS:

Danger/prohibition stickers are applied to the machine where necessary. Look at these prior to using the machine.
43
A1
Use of prescribed PPE obligatory (Safety eyewear and earmuffs)
A2
Read operating instructions before each use.
A3
Use of prescribed PPE obligatory ( Protective Gloves )
A4
Warning! Danger of accidental contact
A5
Do not use discs for wood or metal
A6
Earth connection
24
Under load running
Repose
B1
Do not wash with pressure water jets
C1
Recovery tank water level
D1
Instructions
E1
Laser Accessory / Instructions
F1
Presence energy electric
Battipav srl

Publicidad

Tabla de contenido
loading

Tabla de contenido