Care & Storage; Replacement Parts - Bissell POWERGROOM MultiCyclonic 1654 Serie Manual Del Usario

D
Care & Storage
D1 - Empty the dirt cup
Empty the dirt cup as soon as the dirt
reaches the "FULL" lines on the sides of the
dirt cup.
1. Unplug the vacuum from the electrical
outlet.
2. Press the dirt cup release button on
the carry handle and lift up to remove the
dirt cup.
3. Choose an emptying method. Method
#2 is recommended for allergy suffers.
Method #1 – Hold the dirt cup over a
trash bin and push the emptying
button to open the bottom. Close the
bottom after the dirt empties.
Method #2 – Place a plastic bag over
the bottom of the dirt cup. Push the
emptying button through the plastic
to open the bottom. After the dust
settles, close the bottom and remove
the bag to discard.
4. Replace the dirt cup by placing it back into
the vacuum and pushing down on the carry
handle until it snaps back into place.
D2 - Cleaning the dirt cup filter
Use only BISSELL replacement filters in your
vacuum.
1. Unplug the vacuum from the electrical
outlet.
2. The dirt cup filters can be reached by
removing the dirt cup from the vacuum and
lift up the filter cup release latch. Pull filter
upwards to remove.
3. The dirt cup filter can be can be hand
washed in cold water with a mild detergent.
Rinse well and air dry thoroughly before
placing back onto the filter frame base.
4. Close dirt cup lid and replace dirt cup back
onto product.
www.BISSELL.ca
6
D3 - Replacing the
post-motor filter
The post-motor filter assists in the filtration
process to return cleaner air to the room.
Use only BISSELL replacement filters.
1. Unplug the vacuum from electrical outlet.
2. Remove the filter door (located in the wheel
next to the on/ off switch of the vacuum) by
twisting it counter-clockwise and pulling out
and away from the vacuum
3. The post-motor filter can be hand washed
in cold water with a mild detergent. Rinse
well and air dry thoroughly before placing
back into the vacuum.
4. Replace the filter door by aligning the tabs
up with the slots on inside the wheel and
turning clockwise until you hear a click.
D4 - Cleaning the cyclone
1. Remove the dirt cup from the dirt cup
lid and cyclone assembly by twisting it
counter-clockwise and pulling away.
2. Remove the cyclone by twisting it
clockwise then pulling down and away from
the dirt tank lid, over the secondary cyclone
fine dirt collector.
3. The cyclone can be washed in cold water
with a mild detergent. Make sure it is
completely dry before replacing.
4. Replace the cyclone by sliding it over
the bottom of the secondary cyclone
dirt collector and lining it up with the
lock/unlock arrow before twisting
counter-clockwise until you hear a click.
5. Replace the dirt cup and twist clockwise
to lock.
To reduce the risk of electric shock, turn power switch
o and disconnect plug from electrical socket
before performing maintenance or care.
Do not operate cleaner with damp or wet fi lters
or without all fi lters in place.
This product is intended for household use only and not for
commercial or industrial use. Vacuuming of dust from products
like plaster, concrete or ashes will damage the motor and void
the warranty.
Clearing clogs from the dirt cup
1. Unplug the vacuum from electrical outlet.
2. Remove the dirt cup from the vacuum,
following steps 1-3 of Emptying the dirt cup
on page 6.
3. Remove the dirt cup filter assembly from
the dirt cup, following step 2 of Clean the
dirt cup filter on page 6.
4. Tap the dirt cup filter assembly over a
garbage container to remove any dirt
or debris from the cyclone screen that
surrounds the dirt cup filter.

Replacement Parts

These items are available for purchase as accessories for your BISSELL vacuum:
To purchase visit www.BISSELL.ca.
PART # PART NAME
160-7710 Post-Motor Filter
160-7546 Dusting Brush
160-6494 Hose with Handle
160-7545 Crevice Tool
5. Reach up into the dirt cup to clear any dirt
or debris from the dirt cup.
6. Check to see if there are any clogs
in the suction inlet.
7. After clearing any dirt or debris from
the dirt cup, replace the dirt cup filter
assembly back in the dirt cup following
D2 - Cleaning the dirt cup filter on page 6.
PART # PART NAME
160-5295 Dirt Cup Filter
160-6491 PowerFoot
160-6493 Telescopic Extension Wand
160-7461 Upholstery Tool
7