Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Operations
Special tools
Your bissell vacuum is not only a powerful
carpet and rug vacuum cleaner, it's also a
versatile above floor vacuum cleaner when
you select one of the special tools.
1. Raise handle to upright position.
2. Grasp the hose wand and separate from the
hose wand base.
3. Attach tools by firmly pushing onto vacuum
hose or extension wand.
a. Crevice Tool Use in tight narrow spaces.
b. Dusting Brush Use brush to dust
furniture, blinds, books, lamps, shelves
and baseboards.
c. Extension Wand Use with desired
attachment for a longer reach.
d. TurboBrush® Tool Use rotating brush
action for small flat areas such as stairs and
cushions. Press gently down and pull toward
you in a raking motion; too much pressure
will cause the brush to stop rotating.
e. Long Reach Dusting Tool Use this tool
for dusting large surfaces.
Automatic cord Rewind
1. Gently pull out power cord and stop when
yellow is visible. Do not pull power cord beyond
the red line. Plug cord into electrical outlet.
2. To return cord, turn vacuum power switch
off and remove plug from outlet. Hold plug and
press automatic cord button located below the
power switch (on 1332 and 1327 series models)
to wind cord into reel. Do not allow plug to whip
when rewinding.
www.bissell.com
8
All manuals and user guides at all-guides.com
a.
b.
c.
Tip
» The crevice tool is located
inside the wand
d.
e.
WARnInG
The rotating floor brush continues to rotate while tools
are in use. To reduce the risk of injury from moving parts,
always move the cleaner with the carrying handle at the
back of the cleaner. Always place vacuum cleaner on floor
with handle in upright position when using tools. Never
place your fingers under the cleaner when it is running.
Never place powerfoot on furniture or uneven surfaces. Do
not place vacuum cleaner close enough to objects to pull
them into rotating brush.
Maintenance & Care
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
1. empty the dirt tank when the dirt reaches the
"Full" line on the side. (see page 10)
2. Check the pre-motor filter at least once a
month and clean or replace as needed. To access
the pre-motor filter, remove the easy empty
dirt tank from the vacuum base and push the
lid release button located on the carry handle.
Remove the foam filter from the filter tray.
On select models the carbon filter is included.
if included, the odor-absorbing carbon filter
is located inside the filter tray along with the
foam filter.
notE: black carbon filter is not washable.
3. The post-motor filter assists in the filtration
process to return clean air to the room. Replace
the post-motor filter every three to six months.
To access the post-motor filter, remove the
filter tray located below the easy empty dirt
tank. When the filter becomes dirty, push the
filter through the bottom of the tray to clean or
replace the filter.
notE: the pleated post-motor filter may not
be washed with water or detergent. If dust and/
or debris accumulates on the filter, gently tap
the filter on the side of a garbage container.
note: more frequent filter cleaning or replac-
ing may be necessary if you are vacuuming
new carpet, fine dust, or have allergy concerns.
follow the instructions on the following pages
to perform these simple maintenance steps.
WARnInG
To reduce the risk of electric shock, turn power switch off
and disconnect polarized plug from electrical outlet before
performing maintenance or troubleshooting checks.
2.
lid Release
button
3.
Post-Motor
Filter Tray
notIcE
While vacuuming, certain carpets and low humidity
conditions may generate small static discharges. The
discharges are entirely harmless and are not associated
in any way with the main power supply.
www.bissell.com
9
Publicidad
Tabla de contenido
