Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with an alternating cur-
rent and with the voltage stated on the nameplate.
Charging the battery
1. Connect the appliance plug (H) on the plug-in transformer to
the charging stand socket (E) (Fig. 4ⓐ).
·
The appliance can also be connected directly to
the plug-in transformer for charging (Fig. 2ⓐ/ⓑ).
·
Battery overcharging is prevented thanks to intel-
ligent charge management.
2. Connect the plug-in transformer to the mains socket
(Fig. 4ⓑ).
3. Switch off the appliance using the on/off switch (Fig. 3).
4. Place appliance in the charging stand or connect directly to
the plug-in transformer (Fig. 2ⓐ/ⓑ). The charging process
starts.
·
During the charging operation, the charging indi-
cator on the on/off switch (B) flashes green.
·
After the appliance has been removed from the
charging stand, the charging indicator will go out
(power saving mode).
·
It should take around 45 minutes for the appliance
to charge to full capacity.
5. Once the battery is fully charged, the charging indicator on
the on/off switch (B) shines green.
Battery operation
1. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
·
When the battery is fully charged, the appliance
can be used for up to 75 minutes without mains
connection.
·
The battery power indicator on the on/off switch
(B) will start flashing green when the battery has
< 10% power remaining. The battery needs to be
recharged.
·
The accuracy of the battery power indicator (B)
can be increased by fully discharging the battery
from time to time and then recharging it in one
uninterrupted charging process.
·
In case of insufficient maintenance of the
blade set, the operating time can be reduced
considerably.
Mains operation
1. Connect the appliance plug (H) on the plug-in transformer to
the appliance socket (C) (Fig. 2ⓐ).
2. Connect the plug-in transformer to the mains socket
(Fig. 2ⓑ).
3. Switch on the appliance using the on/off switch and switch
off after use (Fig. 3).
Operation
Cutting with the attachment comb
The appliance can also be operated with an attachment comb.
f The attachment comb has several detent positions for
adjusting the cutting length.
f The further the attachment comb is pushed onto the blade
set, the shorter the cutting length.
Attaching/removing the attachment comb
1. Slide the attachment comb onto the blade set (Fig. 5ⓐ) in
the direction of the arrow until it locks in place.
2. The attachment comb can be removed by pushing it in the
direction of the arrow (Fig. 5ⓑ).
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the appliance before cleaning it or per-
forming any maintenance and disconnect it from
the mains.
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
f Only reconnect the appliance to the power supply
if it is completely dry.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance
and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
Accessories and spare parts are available from your
dealer or our service centre.
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
9
Publicidad
Tabla de contenido
