VTech CS6428-2 Guia De Inicio Rapido

Quick start guide
CS6428-2/CS6429/CS6429-2/
CS6429-3/ CS6429-4/CS6429-5
Introduction
This quick start guide provides you with the basic installation
and setup instructions. A limited set of features are described
in abbreviated form.
Please refer to the online user's manual for complete
.
installation and operation instructions
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone base Telephone
wall jack
power adapter
A DSL filter (not
included) is required
if you have DSL
Electrical
high-speed Internet
outlet not
service
controlled by a
wall switch
Electrical
outlet not
controlled by
a wall switch
Telephone
line cord
Telephone base
Use only the power adapter(s) and battery(ies) supplied with
this product.
Battery installation and charging
Install the battery as shown below. Once you have installed the
battery, you may be able to make and receive short calls. For
best performance, charge the handset battery continuously for
at least 10 hours.
1
Plug the battery connector
securely into the socket.
3
Slide the battery
compartment cover towards
the center of the handset
until it clicks into place.
Charger adapter
Enter the handset menu
1. Press MENU when the telephone is not in use.
2. Press or until the screen displays the desired feature menu.
Press SELECT to enter that menu.
3.
To return to the previous menu, press CANCEL.
•
• To return to idle mode, press and hold CANCEL.
Charger
Set date and time
1. Press MENU when the handset is not in use.
2. Scroll to >SETTINGS then press SELECT.
3. Scroll to >SET DATE/TIME then press SELECT.
4. Use the dialing keys (0-9) to enter the month, date and year
and then press SELECT.
5. Use the dialing keys (0-9) to enter the hour and minute.
6. Press or to choose AM or PM.
7. Press SELECT to save.
Set number of rings
You can set the answering system to answer an incoming call
after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver, the
answering system answers a call after 2 rings when you have new
messages, or after 4 rings when you have no new messages.
1.
2.
2
Place the battery with the
3.
label THIS SIDE UP facing
4.
up and the wires inside the
battery compartment.
5.
Record your own announcement
You can use the preset announcement to answer calls, or replace it
with your own recorded announcement. The announcement can be
up to 90 seconds in length.
1.
4
Place the handset in
2.
the telephone base or
3.
charger to charge.
4.
CHARGE light
remains on when
5.
charging.
IMPORTANT!
Refer to the online user's manual for a full set of installation and
operation instructions. For manual download or customer service,
visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
Press MENU when the handset is not in use.
Scroll to >ANSWERING SYS then press SELECT.
Scroll to >ANS SYS SETUP then press SELECT.
Scroll to ># OF RINGS then press SELECT.
to choose 2, 3, 4, 5, 6 or TOLL SAVER and then
Press or
press SELECT.
Press MENU when the handset is not in use.
Scroll to >ANSWERING SYS then press SELECT twice.
The handset announces, "To play, press 2 . To record, press 7 ."
Press 7 to record.
The handset announces, "Record after the tone. Press 5
when you are done." After the tone, speak towards the
handset microphone. Press 5 when done.
The answering system automatically plays back the newly
recorded announcement. Press 5 to stop the playback at any
time; 2 to replay the recorded announcement; 3 to delete the
recorded announcement; or 7 to record again if desired.
96-007949-070-100