Stanley FATMAX SFMCF800 Manual De Instrucciones página 8

ENGLISH
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (5a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack from
@
the tool
Warning! Make certain the lock-off button is engaged
to prevent switch actuation before removing or
installing battery.
To install battery pack (Fig. C)
● Insert battery pack firmly into tool until an audible click is
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
● Depress the battery release button (6) as shown in
figure D and pull battery pack out of tool.
@
Belt hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal
injury, place the forward/reverse button in the lock-off
position or turn tool off and disconnect battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up
@
can cause injury.
Warning! To reduce the risk of serious personal
injury, ONLY use the tool's belt hook (9) to hang the
tool from a work belt. DO NOT use the belt hook (9)
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or
@
suspend objects from the belt hook.
Warning! To reduce the risk of serious personal
injury, ensure the screw (10) holding the belt hook
is secure.
Note: When attaching or replacing the belt hook (9), use only
the screw (10) that is provided. Be sure to securely tighten
the screw.
The belt hook (9) can be be attached to either side of the tool
using only the screw (10) provided, to accommodate left- or
right- handed users. If the hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw (10) that holds the
belt hook (9) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (10).
8
(Original instructions)
Note: Various trackwall hooks and storage configurations
are available.
Please visit our website www.stanleytools.eu/3 for
further information.
Fitting and removing a screwdriver bit or socket
(Fig. G, H)
This tool is fitted with a quick release chuck to allow for an
@
easy exchange of bits.
Warning! Make certain the tool is locked to
prevent switch actuation before installing or
removing accessories.
● Lock the tool by setting the forward/reverse slider (2) to
the centre position.
● Insert the bit shaft (11) into the chuck (4) (Fig. G).
Note! To remove the bit/socket, pull and hold the chuck
@
collar (3) away from the front of the tool (Fig. H).
Warning! Use only impact rated sockets. Non-impact
sockets may break and cause a hazardous condition.
Inspect socket prior to use to ensure that it contains
no cracks. Use only impact rated accessories.
@
Use
Warning! Let the tool work at its own pace. Do
not overload.
Selecting the direction of rotation (Fig. I)
For tightening, use forward (clockwise) rotation. For loosening,
use reverse (counterclockwise) rotation.
● To select forward rotation, push the forward/reverse
slider (2) to the left.
● To select reverse rotation, push the forward/reverse slider
to the right.
● To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving / nut setting
● Select the appropriate bit / socket for the screw or nut to
be driven.
● Select forward or reverse rotation as described above.
● Hold the tool in line with the fastener.
● Press the trigger (1)
● After tightening, check torque with a torque wrench.
LED work light
The LED work light (7) is activated automatically when
the trigger is depressed. The LED work light will illuminate
when the trigger is partially depressed, before the unit
begins running.
Hints for optimum use
Screwdriving
● Always use the correct type and size of screwdriver bit.
● If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
● Always hold the tool and screwdriver bit in a straight line
with the screw.