Stanley FATMAX SFMCD711 Manual De Instrucciones página 10

ENGLISH
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
Drilling in masonry
For drilling in masonry, set the collar (3) to the hammer
drilling position by aligning the symbol with the marking. Use
carbide tipped masonry bits. Keep even force on the drill. A
smooth, even flow of dust indicates the proper drilling rate.
LED work light (Fig. H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Unit starts immedi- The switch has been
ately upon inserting left in the "on" posi-
battery tion.
Battery pack will Battery pack not
not charge. inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
10
(Original instructions)
Possible solution
Check battery pack
installation.
Check battery pack charg-
ing requirements
The switch must be
moved to "off" to prevent
the tool from immediately
starting when battery is in-
serted.
Insert battery pack into
charger until LED lights.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Allow battery pack to cool
down.
Place on charger
and allow to charge.
@
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
● Do not use any abrasive or solvent-based cleaner.
Z
Protecting the environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
No-load speed
Max. torque
Chuck capacity
Max Drilling capacity
/
Steel/wood masonry
Weight
Charger SFMCB11
Input Voltage
V
AC
Output Voltage
V
DC
Current A
Battery SFMCB201
Voltage 18
V
DC
Capacity Ah 1.5
Type Li-Ion
Level of sound pressure according to EN60745:
Sound pressure (L ) 86.5 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 97.5 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN60745:
2
Drilling into metal (a ) 2.1 m/s , uncertainty (K) 1.5 m/s
h, D
Impact drilling into concrete (a
h, ID
SFMCD711
V
DC
0-350/0-1500
-1
Min
Nm
mm
mm
kg
SFMCB12 SFMCB14
230 230
18 18
1.25 2
SFMCB202 SFMCB204 SFMCB206
18 18
2.0 4.0
Li-Ion Li-Ion
2
2 2
) 10.1 m/s , uncertainty (K) 1.5 m/s
18V
50
13
13/35/13
1.2
230
18
4
18
6.0
Li-Ion