Mastro EXPORY Manual De Instalación E Instrucciones página 5

HANDLING AND TRANSPORT
The equipment is packed on a wooden pallette suitable for lifting by fork lifts or transpallette in order
to avoid possible damages. Upon request or in case of particular transport requirements it could
be packed in a wooden crate (photo A). The wooden packing can be recycled, therefore it has to be
disposed in the special waste plan for recycling. It is advisable to use a wooden board for any handling
of the cabinet in order to avoid damages of the structure.
- Carefully unpack the unit, paying attention so as not to damage it or throw parts and/or accessories (i.e.
screws) away.
- Check that the feet are properly fixed.
- Take away the film which protects the shelves and place them. For this operation we suggest to use
working gloves.
- Check that all the protection films have been taken away from the metal sheet, as well as from the shelves
(we suggest to use working gloves).
COMPLAINTS
On receipt of the refrigerated equipment verify immediately, by unpacking carefully the unit, if there
are transport damages. In case the unit is damaged in any way, notify immediately the driver and,
within 3 days, the shipping company by registered letter.
Every complaint must arrive at the manufacturer within 8 days from receipt of the equipment.
IMPORTANT INSTRUCTIONS AND SUGGESTIONS
Before using the equipment it is important to read these instructions carefully as improper use can
be dangerous. Before connecting the refrigerated unit, make sure that the power supply voltage is as
indicated on the label (photo C).The equipment MUST be connected to a grounded power socket, in
compliance with the current legislation to satisfy the safety requirements.
For usage of the unit, as every electrical device, basic rules have to be followed:
- do not touch or plug the equipment with damp or wet hands or feet;
- do not pull the electric cable to unplug it;
- do not expose it to the atmospheric agents;
- do not allow children to use it without adult supervision;
- before starting any cleaning or maintenance operation, it is necessary to unplug the equi-
pment or to disconnect the equipment by the general power security switch of your shop.
- in case of damages or bad working of the equipment, switch it off and do not attempt to modify it;
- for the cabinets in lenght 250 and 300 cm. in the version with built-in unit, before starting any clea-
ning or maintenance operation, the equipment must be disconnected by the general power security
switch of your shop;
WORKING TEMPERATURE
This equipment is manufactured in conformity with the ambient conditions of climatic class 3 (25° C
- 60% R.H.) EN 441-4.The refrigerated unit maintains its performance characteristics with an ambient
temperature and relative humidity of no more than: +25°C and 60% R.H. ( relative humidity). In case
the ambient conditions are not included in the above mentioned ones, a lower performance must be
expected.
CLEANING
Before switching on the unit, clean the equipment thoroughly, both inside and outside, using warm
water and a solution of bicarbonate of soda (1 tea spoon every 2 liters) or white vinegar. Carefully
dry the unit with a soft cloth. Never use metal pads or abrasive substances. Never use sharp objects;
any damage resulting from the use of these objects will not be covered by warranty.
ELECTRICAL POWER / CONNECTION
First of all, make sure that there is an efficient ground system in compliance with the current legisla-
tion regarding electrical safety.When in doubt, request a careful check from a qualified technician.The
unit is equiped with the plug and the electrical cable mod. Schuco (photo D).
1 - verify that the power supply voltage is as indicated on the machine rate plate (photo C - 230 V
50 Hz monophase)
2 - in case of incompatibility between the socket and the plug of the unit, the plug
should be replaced with a suitable one by a qualified technician
3 - do not connect any other appliance to the same power socket
4 - do not pull the electrical cable or the unit to unplug the equipment from the socket (photo E)
5 - pay attention that the power supply cable is laid in such a way as to prevent it from being dama-
ged or becoming hazardous to people and things.
THE MAIN POWER SUPPLY LINE CAN BE ALTERED ONLY BY A QUALIFIED TECHNICIAN.
6 - In case the power supply cable is damaged, it should be replaced only by a qualified technician.
7 - The Expory with built-in unit in the lengths 250 and 300 cm. is supplied without plug. This will
have to be installed by a qualified technician.
GB
A
B
C
D
E