2. SAFETY INSTRUCTIONS
4
M .
n i a
i a t
frequent work breaks and also by not smoking.
5
L .
m i
t i
h t
l A
h t l
a e
o b
white fi nger disease or carpal tunnel syndrome. Therefore, continual and
regular users should monitor closely the condition of their hands and fi ngers. If
any of the above symptoms appear, seek medical advice immediately.
R •
t u o
e n i
approved safety hard hat to reduce the risk of injury to your head. Noise may
damage your hearing. Wear sound barriers (ear plugs or ear mu ers) to help
protect your hearing. Be particularly alert and cautious when wearing hearing
protection because your ability to hear warnings (shouts, alarms, etc.) is
restricted. Operate your machine as below so that it produces a minimum of
noise and emissions
–
m i l
t i
h t
–
o d
o n
cutting.
–
o d
o n
u t
check the machine by shaking it, if any abnormal sound comes from the
machine, contact the local service fcenteror checking or/and repair.
•
u S
cient personal protection equipment (PPE) is required according to the
operating instructions during the use. Clothing must be sturdy and close-
fi tting, but allow complete freedom of movement. To reduce the risk of cut
injuries, wear the type of overalls, long pants or chaps that contain pads of cut-
retardant material. Avoid loose-fi tting jackets, scarfs, neckties, jewelry, fl ared
or cu ed pants, unconfi ned long hair or anything that could become caught on
branches or brush. Secure hair so it is above shoulder level. Wear the protective
and anti-vibration(AV) gloves. Wear sturdy and slip-resistant boots. Steel-toed
safety boots are recommended. Always wear heavy-duty work gloves (e.g.
made of leather or wear resistant material) when operation. To reduce the risk
of injury to your eyes never operate your power tool unless wearing goggles or
properly fi tted protective glasses with adequate top and side protection. Wear
an approved safety helmet to reduce the risk of injury to your head.
•
s A
o s
n o
containing chemicals, such as unburned hydrocarbons (including benzene)
EN
g n
o o
b d
o o l
i c d
u c r
t a l
h e
r u o
o s
d f
l i a
o y
e p
e v
m
n e
o i t
e n
p d
c e r
o n
y s i
w
r o
s i k
o t
e b
h e
r u o
o s
d f
l i a
o y
e p
r t
n u
h t
e e
g n
e n i
u
n n
e s
e h t
a m
h c
e n i
w
h t i
s a
e h t
n e
n i g
s i e
u r
i n n
n o i
y b
e p
o f r
m r
n i
v g
i t a r
. n o
u a
o i t
s n
o d
o n
g t
a u
n a r
e c i l
s n
d e
n a
l d
i m i
d e t
i t a r
. n o
c e
s s e
l i r a
a y
d n
a
e c c
d a
m a
g a
d e
u m
er or loosened parts, regularly
, g n
i h t
p s
d o r
t c u
e g
284
o g i
u o r
a s
m r
e x e
i c r
s e s
e e t
a h t
y t
u o
w
l l i
o n
s t
o f
c r
t r e
n i a
e p
o i r
s d
W .
r e l
e t a
h t
e e
g n
e n i
r e n
e t a
t s
i x o
e c
h x
u a
f t s
r u d
g n i
t s u
n i a
r a e
n a
o
y l n
r o f
m u
s e