Initial Install Checks; Customer Service - Matrix INDOOR CYCLING LIVESTRONG S Serie Manual Del Usuario

The cycle tune-up must be performed at initial installation of the indoor cycle for optimal performance and
longevity. Please read and follow all instructions below. If the indoor cycle is not installed and tuned as
described, components may wear excessively and the indoor cycle may become damaged. If you have
questions about the installation, please contact MATRIX Fitness Systems.
1RWH 6RPH PDLQWHQDQFH SURFHGXUHV UHTXLUH :' UH¿OODEOH VSUD\ ERWWOH UHFRPPHQGHG RU %UXQR[ VSUD\
lubricant, and White Lithium grease.
 0DNH VXUH WKDW WKH LQGRRU F\FOH LV OHYHO ,I WKH LQGRRU F\FOH URFNV RQ WKH ÀRRU WXUQ WKH
leveling feet underneath the front and/or rear stabilizer until the rocking motion is eliminated.
2. Verify Emergency brake function to assure that emergency brake functions correctly.
3. Brake pad calibration: Turn resistance knob counterclockwise as far as possible (minimum bra-
NLQJ HIIHFW  YHULI\ WKDW WKHUH LV D VOLJKW VHSDUDWLRQ RI WKH EUDNH SDG IURP À\ZKHHO %UDNH SDG
VKRXOG EDUHO\ WRXFK WKH À\ZKHHO ZKHQ UHVLVWDQFH NQRE LV WXUQHG FRXQWHUFORFNZLVH DV IDU DV LW FDQ
go.
4. Apply WD40 or Brunox spray lubricant to the brake pad using the lubrication holes on the plastic
part or the brake pad and externally on the felt pad. Make sure brake pad is thoroughly soaked
IURP HQG WR HQG ZLWK OXEULFDQW VSUD\ 7KHQ ZLSH WKH H[FHVV RII IURP WKH À\ZKHHO
%HVW 3UDFWLFH 8VH D UH¿OODEOH VSUD\ ERWWOH ¿OOHG ZLWK QRQDHURVRO :' SXUFKDVHG E\ WKH JDOORQ
(3.7 L) at the local hardware store.
5. Apply Lithium grease to the threads on the lower end of the brake rod. First, turn the Resistance
knob clockwise until it stops. Apply a small amount of white lithium grease to the threads on the
brake rod above the two lock nuts. Then, turn the resistance knob counter-clockwise until it stops.
6. Apply Lithium grease on the metal threads of all the adjustment knobs.
7. Verify four (4) Allen nuts on RS pulley for tightness. If loose, apply LocTite Threadlocker Blue-242
and retighten.
8. Verify R and L crank arm Allen bolts for tightness. If loose, apply LocTite Threadlocker Blue-242
and retighten.
 9HULI\ EHOW WHQVLRQ &KHFN LI EHOW GULYH LV ¿UPO\ WLJKWHQHG DQG GRHV QRW VOLS ZKLOH ULGLQJ XQGHU UHVLV
tance load. In case that the belt slips, proceed using the adjustment technique as described on
page (28). Please note that a belt drive gear never shows slack. In case of adjustment do
not apply too much tension.
10. Wipe down bike frame with rag moistened with WD-40
11. Some parts of the indoor cycle may become loose during shipment. Check crank arms, check all
exposed screws, bolts, and nuts, and make sure that they are properly tightened.
12. (S Series in the U.S.A. only) Verify that computer is reset for Miles vs. Kilometers and RPM mea
surement is working properly. Please see computer manual for instructions on installation of com
puter.

Customer Service

1. Provide basic maintenance instructions to client and direct them to detailed maintenance instruc-
tions starting at page 24.
 6LJQRII VKHHW SURYLGHG WR FOLHQW WR FRQ¿UP H[SODQDWLRQ RI PDLQWHQDQFH SURFHGXUHVPDQXDO DQG
YHUL¿FDWLRQ RI FRQGLWLRQ RI ELNHV
Version 1.1 2010 SBLS Copyright by Indoorcycling Group GmbH 2010 | www.indoorcycling.com

INITIAL INSTALL CHECKS

ENG 19