Optional Accessories; Replacement Parts - Shure 588SDX Guía De Usuario

Impedance
LO Z: Microphone rated impedance is 150 Ω (270 Ω actual)
for connection to microphone inputs rated low impedance
HI Z: Microphone impedance is "High" for connection to
high-impedance microphone inputs
Sensitivity (at 1,000 Hz)
Open Circuit Voltage*
*1 Pascal=94 dB SPL
Phasing
Positive pressure on the diaphragm produces positive
voltage on pin 2 relative to pin 3 in both HI Z and LO Z
modes
Switch
Built-in ON/OFF switch, lockplate to lock switch ON
Connector
Three-pin professional (male XLR) type
Cartridge Shock Mount
Internal rubber vibration-isolator
Swivel Adapter
Positive action, break-resistant, adjustable through 180_,
slip-out removal for handheld use, designed for mounting
5
on stand with
/ -in.–27 thread
8
Case
Platinum beige enamel die casting with platinum beige
steel grille
Dimensions
See Figure 3
52 mm
(2.129 in.)
OVERALL DIMENSIONS
FIGURE 3
Net Weight
315 grams (11.1 oz)
Certification
Conforms to European Union directives, eligible to bear CE
marking; meets European Union EMC Immunity Require-
ments (EN 50 082–1, 1992); RF radiated (IEC 801–3); ESD
(IEC 801–2); EFT (IEC 801–4).
LO Z HI Z
– 55.5 dBV/Pa – 37.0 dBV/Pa*
(1.7 mV) (14.1 mV)
160 mm
(6.45 in.)
15 mm
(.868 in.)
IMPEDANCE SELECTION
The microphone is shipped connected for low impedance
operation. To change to high impedance, refer to Figure 4 and
proceed as follows:
1. Remove plug element by turning slotted setscrew in
(counterclockwise). Use long-nose pliers to pull plug ele-
ment from case, but be careful not to stretch or break
wires.
2. Disconnect 2-terminal impedance selection socket from
rear of plug element by pulling it off pin 3.
3. Reconnect impedance selection socket so that pin 3 of
plug element is now connected to RED (high-impedance)
lead.
4. Swivel socket so that it does not extend beyond edge of
connector (see inset in Figure 4).
5. Reinsert plug element into microphone; then tighten set-
screw by turning it clockwise.
Î Î Î Î Î Î
Î Î Î Î Î Î Î Î Î Î Î Î
Î Î Î Î Î Î
Î Î Î Î Î Î
IMPEDANCE SELECTION
CONNECTOR END OF MICROPHONE
SWITCH
CARTRIDGE
INTERNAL CONNECTIONS
FURNISHED ACCESSORY
Break-Resistant Swivel Adapter

OPTIONAL ACCESSORIES

Desk Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock Stoppert Isolation Mount
Windscreen (7 colors available)
Cable:
4.6 m (15 ft) or 6.1 m (20 ft) 1-conductor with phone plug
(High Impedance)
7.6 m (25 ft) 2-conductor with 3-pin XLR connectors
(Low Impedance)

REPLACEMENT PARTS

Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen and Grille Assembly
For additional service or parts information, please contact
Shure's Service department at 1–800–516–2525. Outside the
United States, please contact your authorized Shure Service
Center.
2
ELEMENT
IMPEDANCE
SELECTION SOCKET
FIGURE 4
TRANSFORMER TERMINAL HOUSING
BLACK
BLUE (COMMON)
ON
WHITE – LO Z
OFF
YELLOW RED – HI Z
MALE PLUG
FIGURE 5
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . A58WS Series
. . . . . . . . . . . . . . . . . . . C15HZ, C20HZ
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
PLUG
3
1 2
A25D
S37A, S39A
A55M
C25J
R180
RK332G