Bosch BT-ANGLEEXACT 2 Manual Original página 25

To remove the battery (18), press the release buttons (17)
on both sides and pull the battery down and out of the
handle.
Changing the tool – screw head with quick-
change chuck (see figure B)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
BT-EXACT 2 | 4 | 6 | 7 | 8 | 9 | 12
The BT-EXACT series is supplied with a 1/4" quick-change
chuck (QC 1/4").
BT-ANGLE EXACT 2 | 3 | 6
An angled screw head with a 1/4" quick-change chuck is
available for these industrial cordless angle wrenches (art-
icle number 0 607 453 631).
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" quick-change chuck is
available for these industrial cordless angle wrenches (art-
icle number 0 607 453 630).
Inserting the application tool
Pull the quick-change chuck (25) forwards. Insert the applic-
ation tool (1) into the tool holder (2) and release the quick-
change chuck again.
Only use application tools with a matching shank (1/4"
hexagon).
Do not attempt to insert drill bits into this quick-change
chuck.
Industrial cordless angle wrenches and industrial cordless
screwdrivers with a shut-off clutch are not suitable for
drilling. The clutch can shut off automatically and without
warning. If you continue drilling after the clutch has shut off,
the power tool may be wrenched out of your grip until the
shut-off clutch engages again.
Removing the application tool
Pull the quick-change chuck (25) forwards. Take the applic-
ation tool (1) out of the tool holder (2) and release the
quick-change chuck again.
Changing the tool – screw head with external
square
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" square (article number
0 607 453 617) and an angled screw head with a 3/8"
square (article number 0 607 453 620) are available for
these industrial cordless angle wrenches.
BT-ANGLE EXACT 2 | 7 | 17 | 23 | 30
Bosch Power Tools
An angled screw head with a 3/8" square is available for
these industrial cordless angle wrenches (article number
0 607 451 618).
Inserting the application tool
Press the pin on the square of the tool holder (2) inwards,
e.g. using a narrow screwdriver, and slide the application
tool (1) over the square. Ensure that the pin engages in the
recess of the application tool.
Removing the application tool
Press the pin in the recess of the application tool (1) inwards
and pull the application tool off the tool holder (2).
Changing the tool – screw head with internal
hexagon (see figure C)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" internal hexagon is avail-
able for these industrial cordless angle wrenches (article
number 0 607 453 618).
Inserting the application tool
Push the application tool (1) into the internal hexagon of the
tool holder (2) until you hear it engage.
Removing the application tool
Pull the application tool (1) off the tool holder (2), using pli-
ers if necessary.
Operation
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes,
hard hat or hearing protection used for appro-
priate conditions will reduce personal injuries.
Starting Operation
Always set the rotational direction using the rotational direc-
tion switch (13) before starting the power tool:
The power tool will not start if the rotational direction switch
(13) is in the centre (lock-off button).
Setting the rotational direction (see figure D)
Only push the rotational direction switch (13) when
u
the power tool is not in use.
Clockwise: To drive in screws, press the rotational direction
switch (13) all the way to the left.
Anti-clockwise: To loosen or unscrew screws, press the ro-
tational direction switch (13) all the way to the right.
Switching on the worklight
The worklight (20) illuminates the work area in poor lighting
conditions. Switch on the worklight (20) by lightly pressing
the on/off switch (12). If you press down harder on the on/
English | 25
1 609 92A 5P3 | (06.04.2020)