Publicidad
22.Do not make any changes or improvements on the frame of the bouncer. If there is any
damage or missing/ broken parts, contact the shop from which you bought the product.
23.Before each use check, if there are any damages, broken, torn apart or missing parts.
24.The dye and raw materials used for producing this product are safe for the human health.
PARTS
Before assembly of the rocker, take all the parts out of the packing and check if all of the bellow listed
are present. Keep the packages until you finish the assembly completely.
SEE FIGURE PD: 1. Upper frames (2 pcs); 2. Lower frames (2 pcs); 3. Kickstand (1 pc); 4. Support tube
(1 pc); 5.Tube for attaching the music box (1 pc); 6.Tube for the backrest (1 pc); 7.Toy bar (1 pc);
8.Music box (1 pc); 9.Seat pad (1 pc); 10.Bag with screws and nuts (1 pc).
ASSEMBLY STEPS
•After each step check, if the attached parts are well fixed.
•Do not use parts or accessories, which are not provided from the manufacturer, the importer or the
shop, from which you bought the product.
1.Step 1 – See Figure 1: Attach the left upper and lower frames and the kickstand to each other. The
holes on the frames and kickstand, which are for the fixing screw, must be aligned. Slide through
these holes a M5*44 mm screw. Fix it using nut and screwdriver. Mount the kickstand to the right
upper and lower frames in the same way.
2.Step 2 – See Figure 2: Take the support tube and attach it to the rear part of the frames. Align the
holes for the fixing screws. Slide through them screw M5*30 mm and fix it using nut and screwdriver.
3.Step 3 – See Figure 3: Attach the ends of the tube for the music box in the plastic openings of the
side frames. Align the holes of the tube and the frames designed for the fixing screws. Slide on each
side M5*30 mm screw in these holes and fix it using screwdriver.
4.Step 4 – See Figure 4: Attach the tube for the backrest to the plastic holders responsible and for
adjusting the backrest in different laying positions. Press the tube carefully down to fix it in the
holders. Then you will hear a clicking sound. Pull the tube up to check if it is well fixed. Note! The
buttons on the rear part of the tube must be fixed in the corresponding holes in the holders.
5.Step 5 – See Figure 5: Place the seat pad between both of the frames. Then fit the upper rear
pocket to the backrest tube. The bottom rear pocket must fit to the tube of the music box.
Important! Fasten the buckles on both sides of the seat pad. And fasten the buckles of the canopy as
well.
6.Step 6 – See Figures 6 and B: Take the music box and a screwdriver to remove the screw from the
battery compartment cover. Place 2 alkaline batteries AA size correctly as shown on the bottom of
the compartment. Reattach the cover and fix it using the screw. Note! The batteries are not included
in the product. Then attach the music box to the tube of the rocker.
7.Step 7 – See Figure 7: Attach the toy bar to the side plastic holders. Note! The clips on both sides of
the toy bar must be pointed towards you.
USE
1.Check several time if all the screws and belts are well fixed.
2.Place the child in the rocker: Remove the toy bar from the rocker, unfasten the safety belts and
place the child on the seat. Place the belts pad between the legs of the child. Then place the shoulder
belts and fasten the buckles of the waist belts. Make sure that you hear a clicking sound. Fasten the
waist belts so that they fit snugly against your child. Be careful not to fasten them too tightly so as not
to cause discomfort to the child. Then attach the toy bar to the rocker's frame.
3.To calm the baby you can turn on the vibration and melodies function or only the vibration, or only
10
Publicidad
