Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the green light
continuing to blink but with the red light continuously
ON. Once the battery pack has reached an appropriate
temperature, the red light will turn OFF and the charger will
resume the charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
VersaTrack™
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN VersaTrack™ Trackwall. Hooks and accessories
are sold separately. Please refer to the VersaTrack™ Trackwall
accessory sheet for further information.
Shock hazard. Disconnect the
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Filter (Fig. D)
WARNING:
vacuum without its filters.
1. Remove the dust bowl
3
release button
2
and pulling the bowl down and out.
2. Remove the filter
4
by pulling it out of the dust bowl.
3. Twist and pull to remove the pre-filter
4. Install the filter into the dust bowl by aligning the filter
with the dust bowl and placing it firmly into position.
Dust Bowl (Fig. E)
nOTE: It is very important that the filter and pre-filter are
correctly positioned before use.
To install the dust bowl
3
, place it onto the front of the unit
and click firmly into position.
OPERATION
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. F)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
5
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
6
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
On/Off Switch (Fig. G)
nOTE: This product is for dry pick-up only.
•
To switch the vac on, slide the On/Off switch
•
To switch the vac off, slide the On/Off switch
English
To reduce the risk of serious
Never use this cordless hand
by pressing the dust bowl
9
from the filter.
To reduce the risk of serious
into the tool handle, align the
1
forward.
1
back.
7
Publicidad
Tabla de contenido
