Publicidad
Thank you for buying a Texsport Authentic Adventure Gear product. We hope you enjoy your new
propane appliance and that it will serve you for many years to come. We encourage you to read and
understand each step of the set-up and safety operation instructions prior to working with this propane
appliance.
FOR OUTDOOR USE ONLY
GENERAL SAFETY INFORMATION
• NEVER use in an enclosed area.
• DO NOT use heater while sleeping.
• Always use heater in the upright position.
• DO NOT expose the propane cylinder to excessive heat.
• Never operate heater with missing or damaged parts or mantles.
• Always inspect heater, propane cylinder and connections for damage, debris or dirt before attaching
the heater to the propane cylinder.
• Always attach/detach propane cylinder outdoors away from any open flame or pilot lights and only
when the heater is cool.
• When storing or transporting heater, always disconnect the propane cylinder and store it in a cool, well
ventilated location, in an upright position.
• Be sure connection to propane cylinder is tightly secure (hand tighten only) prior to each use.
• Never operate the heater near any flammable liquid or vapors. Keep all flammable or combustible
materials beyond the clearance zone as indicated on the back panel of this booklet.
• Discontinue operation and close valve if:
– ambient temperature drops below -10˚ F.
– there is no fuel remaining in the propane cylinder
– combustion becomes unstable
– lighting cannot be performed quickly and easily
– you experience repeated flame outs
• Never leave heater unattended when hot or in use.
• KEEP OUT OF REACH OF CHILDREN.
NOTE: AN IMPACT TO THE REGULATOR AREA COULD
DAMAGE THE REGULATOR AND FAIL TO LIGHT CORRECTLY,
RESULTING IN MELTING PARTS.
HEATER ASSEMBLY – ASSEMBLE OUTDOORS
Step 1 . Use only the approved 16.4 oz/465 g disposable propane cylinder ap-
proved for use by the United States Department of Transportation DOT-NRC
232/290 M1110.
Step 2 . Make sure that the burner control valve knobs are turned off. Twist in a
clockwise direction.
Step 3 . Please check all connections for leaks using soapy water. Bubbles will form
if there is a leak present.
2E
SI ES ASÍ, HAY UNA FUGA NO USAR LA CALENTADOR SI HAY FUGAS.CUAN-
DO SE ASEGURE DE QUE NO HAY FUGAS, PUEDE ARMAR/ENCENDER SU
Paso 5 . Cuando esté seguro de que no hay pérdidas, podrá proceder a
configurar / encender su calentador.
ENCENDIDO EL CALENTADOR
Paso 1 . Gire la perilla de la válvula de control en el sentido de las agujas del reloj hasta la
configuración alta. Presione el botón de liberación de gas y sostenga; comenzará a
fluir gas.
Paso 2 . Coloque una llama en el componente calefactor.
Paso 3 . Al encender, mantenga el botón de liberación de gas presionado durante 60 se-
gundos y después suelte. La calentador debe permanecer encendida.
Paso 4 . Ahora podrá regular la calentador como desee.
CÓMO UTILIZAR SU CALENTADOR
Paso 1 . Después de encender la calentador, ajuste al nivel de calor deseado.
Paso 2 . Mantenga a los niños, mascotas y materiales inflamables muy lejos del quemador
encendido.
Paso 3 . Mientras que se encuentre encendida, NO toque el área de calor. Durante el funcio-
namiento sólo debe tocarse la perilla de control.
Paso 4 . Las superficies de la calentador están muy calientes y no debe manipularse ni mov-
erse, excepto después de cerrarse.
Paso 5 . Deje enfriar la calentador durante 15 minutos antes de moverla o guardarla.
CALENTADOR.
3S
Publicidad
