DeWalt P2201 Manual De Instrucciones página 4

Model P2201
installation in Steel
The following guidelines are based on the installation of a
fastener in ASTM A 36 structural steel with the point fully
penetrating the steel member. Recommended steel material
thickness ranges from a minimum of 1/8" to a maximum of
3/8". for use in higher strength structural steel, applications
where the point does not penetrate the steel member, or a
thickness of steel greater than 3/8", job site performance
tests are recommended.
Base Material Thickness
Steel base materials should be a
minimum of 1/8" in thickness.
edge Distance
for installations in A 36 steel, 1/2"
is the recommended minimum edge
distance.
Spacing
The recommended minimum distance
between fastenings is 1-1/2" center
to center for installations in ASTM A
36 steel.
Fastener length Selection in Steel
for permanent applications when using pins in steel, first
determine the thickness of the fixture to be fastened. To this,
add the thickness of the steel base material plus a minimum
of 1/4" to allow for proper point penetration. This will be the
minimum fastener shank length required. Do not select a
fastener length longer than that required for the application.
An excessively long shank can burnish or polish the hole
created in the steel resulting in a reduction in load capacity.
for removable applications with threaded studs, the
shank length required is equal to the thickness of the steel
base material plus a minimum of 1/4" to allow for proper
point penetration. This will be the minimum fastener shank
length required. Do not select a shank length longer than
that required for the application. An excessively long shank
can burnish or polish the hole created in the steel resulting
in a reduction in load capacity. To determine the minimum
threaded length, add the thickness of the fixture and the nut
/ washer thickness. The nut and washer thickness is equal to
the nominal thread diameter.
Do not over tighten threaded studs, the maximum
tightening torque is listed in the table below. Use of a nut
setter is recommended to reduce the possibility of over
tightening the fasteners. for critical applications, perform a
job site test.
P2201
Fastener Selection Guide
.300 head Diameter Drive Pins
CaT.
no.
DDf3011000 1/2" k
DDf3011050 5/8" k
DDf3001100 3/4"
DDf3001150 1"
DDf3001200 1-1/8"
DDf3001250 1-1/4"
DDf3001300 1-1/2"
DDf3001350 1-3/4"
1/8"
DDf3001400 2"
DDf3001450 2-1/4"
1/2"
DDf3001500 2-3/8"
DDf3001550 2-1/2"
DDf3001600 2-3/4"
DDf3001650 3"
1-1/2"
.300 head Diameter Drive Pins with Top hat
CaT.
no.
DDf3031000 1/2" k
DDf3031050 5/8" k
DDf3031100 3/4"
DDf3031150 1"
.300 head Diameter Step Shank Pins
CaT.
no.
DDf3041000 3/4" Step Shank 100
DDf3041050 1" Step Shank 100
.300 head Diameter Drive Pins - Master Pack
CaT.
no.
DDf301100M 1/2" k
DDf301105M 5/8" k
DDf300110M 3/4"
DDf300115M 1"
DDf300125M 1-1/4"
DDf303100M 1/2" k TH
DDf303105M 5/8" k TH
DDf303110M 3/4" TH
DDf303115M 1" TH
.300 head Diameter Drive Pins with 3/4" Washer
CaT.
no.
DDf3051100 3/4"
DDf3051200 2-1/2"
.300 head Diameter Drive Pins with 7/8" Washer
CaT.
no.
DDf3061150 1"
DDf3061250 1-1/4"
DDf3061300 1-1/2"
DDf3061400 2"
DDf3061550 2-1/2"
DDf3061650 3"
.300 head Diameter Drive Pins with 1" Washer
CaT.
no.
DDf3071000 1-1/4"
DDf3071050 1-1/2"
DDf3071250 2"
DDf3071150 2-1/2"
DDf3071200 3"
4
Cat. No. DDF211022P
Shank STD. STD.
lengTh Box CTn.
100 5000
100 5000
100 5000
100 5000
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
Shank STD. STD.
lengTh Box CTn.
100 5000
100 5000
100 5000
100 5000
Shank STD. STD.
lengTh Box CTn.
1000
1000
Shank STD. STD.
lengTh Box CTn.
1000 5000
1000 5000
1000 5000
1000 5000
1000 5000
1000 5000
1000 5000
1000 5000
1000 5000
Shank STD. STD.
lengTh Box CTn.
100 1000
100 1000
Shank STD. STD.
lengTh Box CTn.
100 1000
100 1000
100 1000
100 1000
100 1000
100 1000
Shank STD. STD.
lengTh Box CTn.
100 1000
100 1000
100 1000
100 1000
100 1000
heaD Shank WT./
Dia. Dia. 100
.300 .143 .5
.300 .143 .5
.300 .143 .5
.300 .143 .6
.300 .143 .7
.300 .143 .8
.300 .143 .9
.300 .143 1.1
.300 .143 1.2
.300 .143 1.2
.300 .143 1.3
.300 .143 1.4
.300 .143 1.6
.300 .143 1.9
heaD Shank WT./
Dia. Dia. 100
.300 .143 .5
.300 .143 .5
.300 .143 .5
.300 .143 .6
heaD Shank WT./
Dia. Dia. 100
.300 .143/130 .5
.300 .143/130 .6
heaD Shank WT./
Dia. Dia. 100
.300 .143 .5
.300 .143 .5
.300 .143 .5
.300 .143 .6
.300 .143 .8
.300 .143 .5
.300 .143 .5
.300 .143 .5
.300 .143 .6
heaD Shank WT./
Dia. Dia. 100
.300 .143 1.6
.300 .143 2.5
heaD Shank WT./
Dia. Dia. 100
.300 .143 1.9
.300 .143 2.0
.300 .143 2.1
.300 .143 2.4
.300 .143 2.7
.300 .143 3.0
heaD Shank WT./
Dia. Dia. 100
.300 .143 2.2
.300 .143 2.3
.300 .143 2.6
.300 .143 2.9
.300 .143 3.2