Refined Salt And Rinse Aid; Measuring Out The Refined Salt; Measuring Out The Rinse Aid - Hotpoint Ariston ELTF 11M121 Manual De Instrucciones

Refined salt and
rinse aid,
Only use products which have been specifically designed
EN
for dishwashers. Do not use table salt or industrial salt.
Follow the instructions given on the packaging.
If you are using a multi-function product, we recommend
that you add salt in any case, especially if the water is hard
or very hard. (Follow the instructions given on the packaging.)
If you do not add salt or rinse aid, the LOW SALT
*
LOW RINSE AID indicator lights will remain lit.

Measuring out the refined salt

The use of salt prevents the formation of LIMESCALE on the
dishes and on the machine's functional components.
• It is important that the salt dispenser be never empty.
• It is important to set the water hardness.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• When the LOW RINSE AID indicator light in the control panel
*
is lit ;
• When the green float
longer visible.
• See autonomy in the water hardness table.
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. Only the first time you do this: fill the water
dispenser up to the edge.
3. Position the funnel
fill the salt container right up to its edge
(approximately 1 kg); it is not unusual for a
little water to leak out.
4. Remove the funnel and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on.
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
Whenever you need to add salt, we recommend carrying
out the procedure before the washing cycle is started.
Setting the water hardness
For perfect water softener operation, it is essential that the
adjustment be based on the water hardness in your house. Ask
your local water supplier for this information. The factory setting
is for medium water hardness.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Hold down button P for 5 seconds until you hear a beep.
• Switch it on using the On/Off button
• The current selection level number and salt indicator light flash.
• Press button P to select the desired hardness level (see
hardness table).
• Switch it off using the On/Off button
• Setting is complete!
*
Only available in selected models.
26
*
on the cap of the salt dispenser is no
(see figure)
Water Hardness Table
level °dH
1 0 - 6
2 6 - 11
3 12 - 17
4 17 - 34
*
*
and 34 - 50
5
For values between 0°f and 10°f, we do not recommend the use of salt.
A setting of 5 may increase cycle duration.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees – mmol/l = millimoles per litre)

Measuring out the rinse aid

Rinse aid makes dish DRYING easier. The rinse aid dispenser
should be filled:
• When the LOW RINSE AID indicator light on the panel/display
*
;
is lit
• When the dark optical indicator
becomes transparent.
and
1. Open the dispenser "D" by pressing and pulling up the tab
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch in the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may want to adjust the quantity of rinse aid used.
• Switch the dishwasher on using the On/Off button.
• Switch it off using the On/Off button
• Press button P three times - a beep will be heard.
• Switch it on using the On/Off button
• The current selection level number and rinse aid indicator
light flash.
• Press button P to select the level of rinse aid quantity to be
supplied.
• Switch it off using the On/Off button
• Setting is complete!
If the rinse aid level is set to ZERO, the rinse aid will not be
supplied and the low rinse aid indicator light will not be lit if you
run out of it.
A maximum of 4 levels can be set according to the dishwasher
model. The factory setting is for a medium level.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
Average autonomy
salt dispenser with 1
wash cycle per day
°fH mmol/l months
0 - 10 0 - 1 7 months
11 - 20 1.1 - 2 5 months
21 - 30 2.1 - 3 3 months
31 - 60 3.1 - 6 2 months
61 - 90 6.1 - 9 2/3 weeks
*
on the dispenser door "D"