Extended Menu - Seav LRX 2035 NEW READER Manual De Usario

During programming the radio control key of the control unit can be used instead of the SET
key, if stored previously.
4) T. PAUSA: (Automatic closing time programming max. 4 minutes)
The control unit is supplied by the manufacturer without automatic closing. If you wish to
enable automatic closing, proceed as follows: using the SEL key to move to the flashing
T. PAUSA LED, press the SET key briefly, then wait for the amount of time you wish to set
for automatic closing; briefly press the SET key again, and in that moment the automatic
closing time will be memorised and the T. PAUSA LED will stay on steady. If you wish to
restore the initial condition (without automatic closing), move to the flashing T. PAUSA
LED, then press the SET key twice within 2 seconds. The LED will switches off and the
operation is complete.
When programming, you can use the radio control key on the control unit instead of the
SET key, if stored previously.

EXTENDED MENU 1

The control unit is supplied by the manufacturer with the option of selecting only the
functions listed in the main menu.
If you wish to enable the functions described in extended menu 1, proceed as follows:
press and hold the SET key for 5 seconds, after which the T. MOT. and T. PAUSA LEDs
will start flashing alternately. The user then has 30 seconds to select the functions for
extended menu 1 using the SEL and SET keys. After another 30 seconds the control unit
will go back to the main menu.
———————————— — EXTENDED MENU 1 ————————————
Reference LED LED Off
A) CODE remote PGM = OFF
B) LAMP/CORT Step-by-Step
C) T. MOT. Alternate ON/OFF flashing light
D) T. PAUSA. Alternate ON/OFF flashing light
A) CODE (Remote programming of radio control):
The control unit allows the transmission code to be programmed remotely, without using
the SEL key on the unit itself.
The remote transmission code can be programmed as follows: continuously send a pre-
viously-stored radio control code for more than 10 seconds. At this point the control unit
switches to programming mode, as described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with the remote transmission code pro-
gramming function disabled. If you wish to enable the function, proceed as follows: check
that extended menu 1 is enabled (T. MOT. and T. PAUSA LEDs flash alternately), use the
SEL key to move to the flashing CODE LED, then press the SET key: at this point the CODE
LED will light up steady and programming is complete. Repeat the procedure to restore
the previous configuration.
B) LAMP/CORT. (Step-by-Step / Automatic operation) :
The control unit is supplied by the manufacturer with Automatic mode disabled. If you
wish to enable the function, proceed as follows: check that extended menu 1 is enabled
(T. MOT. and T. PAUSA LEDs flash alternately), use the SEL key to move to the flashing
LAMP/CORT LED, then press the SET key: at this point the LAMP/CORT LED will light up
steady and programming is complete.
Accordingly, using either the Radio Control, Transponder, Digital keyboard, Smartphone
or the low voltage push button panel to operate the frame, you will obtain the following
function: the first impulse commands opening until the motor time expires, the second
impulse commands frame closing. If an impulse is sent before the motor time expires, the
control unit changes the direction of motion in the opening and closing phases. Repeat
the procedure to restore the previous configuration.
EXTENDED MENU 2
The control unit is supplied by the manufacturer with the option of selecting only the
functions listed in the main menu.
If you wish to enable the functions described in extended menu 2, proceed as follows:
access extended menu 1 (as described in the relative paragraph), then press and hold
the SET key down again for 5 seconds, after which the T. MOT. and T. PAUSA LEDs will
start flashing simultaneously. The user then has 30 seconds to select the functions for
extended menu 2 using the SEL and SET keys. After another 30 seconds the control unit
LED On
will go back to the main menu.
remote PGM = ON
———————————— EXTENDED MENU 2 ————————————
Automatic
Riferimento Led
A) CODE
B) LAMP/CORT
C) T. MOT.
D) T. PAUSA.
A) CODE (Anti-Pass-Back) :
The control unit is supplied by the manufacturer with the Anti-pass-back function disabled. If
you wish to enable the function, proceed as follows: check that extended menu 2 is enabled
(T. MOT. and T. PAUSA LEDs start flashing simultaneously), use the SEL key to move to the
flashing CODE LED then press the SET key: at that point the CODE LED will light up steady and
programming is complete. This way the control unit will operate in Antipassback mode, i.e.
using a pair of BeSafe Reader New, BeSafe KeyBoard and/or BeSafe NFC (set with different
17
LED Off LED On
Anti-Pass-Back = OFF
Anti-Collision (pedestrian) CH = OFF
Simultaneous ON/OFF flashing
Simultaneous ON/OFF flashing
Anti-Pass-Back = ON
Anti-Collision (pedestrian) CH = ON