Populo RTK-107 Manual De Usuario página 3

3.6 Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry
or long hair, can get caught in moving parts resulting in serious injury.
3.7 If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
4. Power tool use and care
4.1 Do not force the power tool. Use the correct power tool for your application. The correct power tool will do a better and safer job when
used for its designed purpose.
4.2 Do not use the power tool if the on/off switch is malfunctioning. Any power tool that cannot be controlled with the switch is dangerous and
must be repaired.
4.3 Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing
accessories, or storing power tools. This helps reduce the risk of starting the power tool accidentally.
4.4 Store idle power tools out of the reach of children. Do not allow persons unfamiliar with the power tool to operate it without first reading
these instructions. Power tools are dangerous in the hands of untrained users.
4.5 Properly maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may
affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
4.6 Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to
control.
4.7 Use the power tool, accessories, and tool bits, etc. by following these instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those intended could create a hazardous situation.
5. Service
5.1 Have your power tool serviced by a qualified repair person using only identical replacement parts.This will ensure that the power tool is
properly and safely maintained.
5.2 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to prevent any
potential hazard.
ROTARY TOOL SAFETY WARNINGS
This appliance should only be used by able-bodied individuals. Younger persons should only use the tool when supervised by a responsible
person who can ensure the tool is being used safely. Young children should not be allowed to use the tool - it is not a toy!
WARNING! Safety warnings common for grinding, sanding, wire brush-
ing, polishing or abrasive cutting-off operations.
● This power tool is intended to function as a grinder, sander, wire brush, polisher or cut-off tool. Read all safety warnings, instructions,
illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury.
● Operations for which the power tool was not designed may create a hazard and cause personal injury.
● Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe operation.
● The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster
than their rated speed can break and fly apart.
● The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded or controlled.
● Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbor hole of the
accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of control.
● Do not use a damaged accessory. Before each use, inspect the accessory for potential damage (i.e., abrasive wheels for chips and cracks,
backing pad for cracks/tears or excess wear, wire brush for loose or cracked wires.) If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and any standers away from the
plane of the rotating accessory and run the power tool at maximum no load speed for one minute. Use caution as damaged accessories will
normally break apart during this testing.
● Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear
dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
● Keep by standers a safe distance away from work area. Anyone entering the work area must wear personal protective equipment.
Fragments of workpiece or of a broken accessory may become airborne and cause injury beyond immediate area of operation.
● Hold the power tool by insulated gripping surfaces only, especially when performing an operation where the cutting accessory may
contact hidden wiring or its own cord. If the cutting accessory comes into contact with a live wire, it may cause exposed metal parts of the
power tool to become live too, resulting in electric shock to the operator.
● Position the cord clear of the spinning accessory. If you lose control of the tool, the cord may be cut or snagged, and your body pulled into
the spinning accessory resulting in potential injury.
● Never lay the power tool down until the accessory has come to a complete stop or the spinning accessory may grab the surface and pull the
power tool out from your control.