Additional Safety Instructions; Noise And Vibration - Flex SE 14-2 125 Instrucciones De Funcionamiento

 Maintain a firm grip on the power tool
and position your body and arm to allow
you to resist kickback forces.
Always use auxiliary handle, if provided,
for maximum control over kickback
or torque reaction during start-up.
The operator can control torque reactions
or kickback forces, if proper precautions
are taken.
 Never place your hand near the rotating
accessory.
Accessory may kickback over your hand.
 Do not position your body in the area
where power tool will move if kickback
occurs.
Kickback propels the electric power tool
in the direction opposite to the movement
of the sanding disc at the point of pinching.
 Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory.
Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory
and cause loss of control or kickback.
This causes a loss of control or kickback.
 Do not attach a saw chain woodcarving
blade or toothed saw blade.
Such blades create frequent kickback and
loss of control.

Additional safety instructions

t^okfkd>
qçìÅÜáåÖ=çê=áåÜ~äáåÖ=Ü~êãÑìäLíçñáÅ=Çìëí=
áë=~=Ü~ò~êÇ=íç=íÜÉ=çéÉê~íçê=~åÇ=íç=éÉçéäÉ=
áå=íÜÉ=îáÅáåáíóK
 It is not recommended to sand lead paint.
Lead paint should be removed by a specia-
list only.
 Do not work on materials which release
hazardous substances (e.g. asbestos).
Take precautions if hazardous, combustible
or explosive dust is likely to occur.
Wear protective dust mask.
Use dust extraction system.
a^j^db=ql=molmboqv>
 The mains voltage and the voltage
specifications on the rating plate must
correspond.
18
SE 14-2 125/SE 14-2 150

Noise and vibration

The noise and vibration values have been
determined in accordance with EN 60745.
The A evaluated noise level of the power tool
is typically:
– Sound pressure level:
– Sound power level:
– Uncertainty:
Total vibration value
(when grinding with sanding sheet):
– Emission value:
– Uncertainty:
t^okfkd>
qÜÉ=áåÇáÅ~íÉÇ=ãÉ~ëìêÉãÉåíë=êÉÑÉê=íç=åÉï=
éçïÉê=íççäëK=a~áäó=ìëÉ=Å~ìëÉë=íÜÉ=åçáëÉ=~åÇ=
îáÄê~íáçå=î~äìÉë=íç=ÅÜ~åÖÉK
klqb
The vibration emission level given in this infor-
mation sheet has been measured in accor-
dance with a standardised test given
in EN 60745 and may be used to compare
one tool with another. It may be used
for a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool.
However if the tool is used for different appli-
cations, with different accessories or poorly
maintained, the vibration emission may differ.
This may significantly increase the exposure
level over the total working period.
For a precise estimation of the vibration load the
times should also be considered during which
the power tool is switched off or even running,
but not actually in use. This may significantly
decrease the exposure level over the total
working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
`^rqflk>
tÉ~ê=É~ê=éêçíÉÅíáçå=~í=~=ëçìåÇ=éêÉëëìêÉ=
~ÄçîÉ=UR=Ç_E^FK
79.7 dB(A);
90.7 dB(A);
K = 3 dB.
2
a < 2.5 m/s
h, DS
2
K = 1.5 m/s