Publicidad
Idiomas disponibles
Idiomas disponibles
BASE SETUP
See Owner's Manual for complete operating instructions.
PART LIST
Before discarding the packing materials ensure all the parts are accounted for.
Some parts may be attached to the base or inside boxes, please inspect carefully.
(4) Legs &
(1) Wireless
(3) AAA
Washers
(1) Power
*6 legs included with
Remote
Batteries
Cord
King/Cal king
STEP 1
Always use two people when setting up the base.
Place the bed base box in a desired location with the bottom
of the box facing up.
Remove the binding straps and packing materials, making
sure not to puncture the box with any sharp objects.
STEP 2
*If installing a King/Cal King base please refer to the
instructions on next page.
If installing a headboard, please see headboard bracket
installation instructions in Owner's Manual on page 16.
Install the legs by
threading the washer over
the bolt of the leg with the
recessed side facing the
leg, and tighten by hand.
Do not over tighten.
STEP 3
To set up and sync two bases with the Smart Sync Cord and
connecting strap, see installation instructions in Owner's Manual
Uncoil the Power Down Box from the
frame.
Place box on the ground. Ensure that
it is easily accessible when the base is
turned to its upright position.
STEP 4
Uncoil input cord (connected to
control box's power port) and plug
into Power Supply.
Only included in split bases:
(1)
(1) SmartSync
Connecting
Strap
Optional Equipment:
(not included)
(1) Power
(1) Mattress
•
Surge Protector
(1) Battery
Supply
Retainer Bar
Backup
•
(2) 9V Batteries
STEP 5
Uncoil the Power Cord and connect
to the Power Supply. Place Power
Supply on the ground and extend
from the base. Ensure that the Power
Supply and all attached cords are
directed toward the desired surge
protector.
STEP 6
Carefully flip the base over on to its legs. Important: Two
people are required to move the bed base. Do not drag
across the floor. Do not rest frame on its side, excessive
pressure may damage the legs.
STEP 7
Plug the base into a power source. A surge protector is
strongly recommended.
STEP 8
Install (3) AAA batteries in remote control.
Quickly test functions to verify proper
setup before placing mattress on base.
Return the base to a flat position before
placing the mattress on top.
STEP 9
Slide the left side of the mattress retainer bar into the
bracket. Pull the retainer bar into the opposite bracket and
secure the right side.
Test all functions on the base to ensure proper setup. For
more information please see Owner's Manual
For Tempur-Pedic
customer service call:
®
U.S. 1-800-821-6621 | Canada: 1-800-887-4321
México: 01-722-273-1810
Always use 2 people when setting up the base.
KING/CAL KING ADDITIONAL PART LIST*
Before discarding the packing materials ensure all the parts are accounted for.
Some parts may be attached to the base or inside boxes, please inspect carefully.
®
Cord
(2) Long Bolts
*Located in the box labeled: Foot (Box 2 of 2)
STEP
2.1
Push and align the head and foot sections together. Make
sure to align the leg thread holes with top frame as seen
in Fig. A and side hole as seen in Fig. B.
Fig. A
2.2
STEP
Once aligned, slide long bolt through the side hole shown
in Fig. C and Fig. D. Secure bolt using one of the washers
and wing nuts provided. Repeat this step for the other
side of the base.
Fig. C
To install Headboard Brackets (sold separately)
see instructions on page 17 of the Owner's Manual
KING/CAL KING SETUP
(2) Wing nuts
(2) Washers
2.3
STEP
Attach the legs by screwing them into the leg threads.
Do this on all four corners and both sides of the middle
section.
Fig. G
Fig. B
2.4
STEP
Connect the head motor and
head massage cables to the
appropriate ports labeled on
the Control Box.
Fig. D
Connect the USB charger
to the splitter cord.
Please continue with Step 4 on previous page.
Fig. E
Fig. F
Setup is now complete!
Publicidad
