Publicidad
Idiomas disponibles
Idiomas disponibles
2.
Prepare
detergent
solution
as required
by manufacturer.
3.
Place small filter end of detergent
siphoning
tube into
detergent
container.
4.
Make sure black spray tip is installed.
NOTE:
Detergent
cannot
be applied with the high
pressure
spray tips (White,Yellow,
or Red).
5.
Make sure garden
hose is connected
to water
inlet.
Check
that high pressure
hose is connected
to spray
gun and pump and start engine.
CAUTION
.
. When inserting filter into a detergent solution bottle, route
tube to keep it from inadvertently contacting hot muffler.
S.
6.
Apply detergent
to a dry surface, starting
at lower
portion
of area to be washed
and work
upward, using
6.
long, even, overlapping
strokes.
7.
Allow detergent
to soak in between
3-5 minutes
before
washing and rinsing. Reapply as needed
to
7.
prevent
surface from drying. DO NOT allow detergent
to dry on (prevents
strealdng).
IMPORTANT:You
must flush the chemical
injection
system
after each use by placing the filter into a bucket
of
clean water, then run the pressure
washer
in low pressure
for 1-2 minutes.
Pressure Washer
Rinsing
Wash
and Rinse Surface
This pressure
washer
permits
regulation
of output
water
pressure
by varying the engine speed.The
variable
pressure
control
lever found on the front of the engine may be set,
as shown
in Figure 15:
Pressure
Low
to
High
Duty
Light
Medium
Heavy
Application
Auto
Concrete
Paint removal
Boat
Driveway
Degreasing
Furniture
Deck
After you have applied
detergent,
scour the surface
and rinse it clean as follows:
I.
Engage trigger lock on spray gun.
2.
Remove black chemical nozzle from nozzle extension.
3.
Select and install desired high pressure nozzle following
instructions
"How to Use Spray Tips".
Keep spray gun a safe distance
from the area you plan
to spray.
WARNING
Keep spray nozzle
between
8 to 24 inches
away from cleaning
surface.
Operate
this unit on a stable surface.
Be extremely
careful if you must use the pressure washer from
a ladder, scaffolding or any other relatively
unstable location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when gun kicks back.
Adjust
spray pressure
by sliding variable
pressure
contol
lever left or right, as shown
in Figure
I I.
Apply
a high pressure
spray to a small area and then
check
the surface
for damage.
If no damage
is found,
you can assume
it is okay
to continue
rinsing.
Start
at top
of area
to be rinsed,
working
down
with
same
overlapping
strokes
as you
used
for
cleaning.
Cleaning
Detergent
Siphoning
Tube
If you used the detergent
siphoning tube, you must flush it
with clean water before stopping the engine.
I.
Place chemical injection siphon/filter
in a bucket full of
clean water.
2.
Engage trigger
loci< on spray gun.
3.
Attach
black low pressure
spray tip.
4.
Flush for 1-2 minutes.
5.
Shut off engine.
6.
ALWAYS point gun in a safe direction
and squeeze
spray gun trigger to release
retained
high water
pressure.
IMPORTANT:
Spray gun traps high water pressure, even
when engine is stopped and water
is disconnected.
Automatic
Cool
Down
System
(Thermal
Relief)
If you run the engine
on your pressure
washer
for
3-5 minutes
without
pressing
the trigger
on the spray gun,
circulating
water
in the pump can reach temperatures
above
125°EThe
system
engages to cool the pump by
discharging
the warm
water
onto
the ground.
Publicidad
