Health Zenith SL-5502 Manual Del Usuario

Compact Twin 150 Watt Halogen
The Heath ® /Zenith Compact Twin Halogen disperses light over a wide area. It
includes two 150W halogen lamps, mounting plate for standard junction box and is for use with 120VAC.
FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.
• Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.
• Keep fixture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).
• Use up to 150 watt lamp maximum per lampholder.
Fixture Installation Instructions.
To avoid Electrical Shock:
• Turn off the circuit breaker or remove the fuse protecting the
lighting circuit.
• Grounding and installations must comply with local codes and
the National Electric Code (Canadian Electrical Code).
• This product should be mounted on a grounded junction box
and must be used with a threaded cover plate.
• Permanently mount the fixture to a building or pole. This fixture
is for outdoor use and is wall and eave mountable.
Connect all white
wires together
Cover Plate
Wiring Fixture
❒
Connect the lamp wires to the power source wiring. Secure with
wire connectors.
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of five years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge
to you. Light bulbs are not covered. To obtain a refund or a replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered
by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty
does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a customer
uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESEN-
TATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA
SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO
ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.
© 2003 DESA Specialty Products™
To Avoid Fire or Burn Hazards:
Junction box
ground wire to
green ground
screw on fixture
Connect all black
wires together
No Service Parts Available for this Product
FIVE YEAR LIMITED WARRANTY
Model SL-5502
❒
Attach the cover plate to the junction box
(Apply silicon caulk between cover plate
and junction box for a raintight seal).
Keep the fixture horizontal (within +/-
4°) so the bulb inside is horizontal. If the bulb is not horizontal, the
bulb may darken or shatter and fail prematurely.
❒
Loosen the side bolt connected to the arm to aim the fixture up
and down.
❒
For a rain tight seal, caulk the aiming arm joint with silicon
caulking compound.
Bulb Installation and Relamping.
Important: Use a clean glove or cloth when handling the new bulb.
Oil from your hand may cause the bulb to crack when the fixture
heats up and result in premature failure. Use isopropyl (rubbing)
alcohol to clean the bulb if it is touched with your bare hands.
❒
When relamping, turn power off and let the fixture cool.
❒
Open glass cover and remove the old bulb by pushing the bulb
towards the right until the left side of the bulb is clear of the left
socket.
❒
To insert the new bulb push the bulb into the right socket so the
bulb is properly seated in the sockets.
❒
Re-install the glass cover.
❒
Reconnect the power.
+/- 4°
595-5573-05