Adjusting - Femi 1050 3D Instrucciones Para El Uso Y Manutencion

NOTE: Your mitre–saw's electrical system is
equipped with an under–voltage relay which
automatically opens the circuit when the voltage
falls below a minimum pre–established limit
and which prevents the self–reset of machine
functions when voltage returns to normal levels.
If the machine stops involuntarily, do not be
alarmed. Make sure that there has not been a
voltage failure in the electrical system.
3

ADJUSTING

WARNING: All the adjustment procedures
illustrated below must be performed when the
machine's motor is turned off.
WARNING: The machine leaves the factory with the
hard stop positions already calibrated. Should any
further adjustment be required, please contact an
authorized after sales service centre.
3.1 ADJUSTMENT OF CUTTING ANGLE–HEAD
ROTATION (Fig. 17)
This mitre–saw can cut both to the left and to the right.
The pre–set positions are: 15° – 22°30' – 30° and 45°.
To position the machine as above, loosen knob 5 Fig.
9, release the machine head by pushing the lever 6 Fig.
10 downwards and rotate the rotary support by using the
handgrip 5.
The head stops automatically each time the pointer 27
is aligned with the corresponding position etched on the
graduated scale of the rotating plate.
For all the intermediate positions, once the indicator has
been aligned with the position indicated on the relative plate,
block the swivel support using knob 5.
3.2 ADJUSTMENT OF CUTTING ANGLE – HEAD
ANGLE (Fig. 18)
WARNING : ensure that arm is securely fi xed when
bevelling.
The machine head can be tilted to a maximum of 45° to
the left.
Release the knob 10 - Fig. 12 and the knob 9 - Fig. 12
(on the rear part of the machine) and tilt the head until it
comes to rest on the stopper at an angle of 45° (already
calibrated during testing).
Block again the head with the knob 10.
For all other intermediate positions, align index 28 on the
rear of the head with the corresponding position marked on
the graduated scale of the swivel joint.
WARNING: During double angle cutting (rotation
plus head tilting) hold the work piece securely to
the machine using the right hand and guide the
lowering of the head with the left hand (Fig. 28).
3.3 ADJUSTMENT HEIGHT OF UPPER WORK
SURFACE (Fig. 11-21)
JUST FOR CIRCULAR SAW
WARNING: When working on the upper surface, it
is absolutely necessary to install the lower safety
guard supplied 11 - Fig. 19.
To install the guard, with the head raised, insert the guard
in its seat, then lower the head and lock the body in this
position using locking pin 4 - Fig. 20.
To adjust the height of the upper work surface to obtain
desired cutting widths, follow the instructions below:
– Slacken lever 14 - Fig. 21 by turning it anti–clockwise.
– Turn knob 15 anti–clockwise until the blade comes out
of the work surface by the required height.
– tighten lever 14.
3.4 ADJUSTMENT OF BEARING BRACKET (Fig. 19)
JUST FOR CIRCULAR SAW
The bearing bracket 14 can be brought closer or moved
further away from the blade in order to cut planks of a
preset size.
Slacken the handwheel 29 and move the bracket 14 until the
index on the support matches the corresponding position on
the graduated scale marked on the work surface, bearing
in mind that the position indicated by the bracket on the
graduated scale corresponds to the distance from the
surface of the cutting blade.
3.5 WEDGE REGULATION (Fig. 6)
To ensure the dividing wedge is in the correct position,
keep it at a distance of between 3 mm – 8 mm from the
tooth of the blade.
4 USE – SAFETY WARNINGS
After having performed all the above procedures and
operations, you may begin cutting, paying attention to the
following safety measures.
WARNING:
• Always keep hands away from the cutting area
and do not try to approach it when the machine
is running.
• It is severely prohibited to use the machine for
carrying out blind cuts.
• Before each operation, always check that
all locking knobs and levers are securely
tightened.
• It is severely prohibited to use the machine if
the power switch cannot turn the machine itself
on or off.
• Before starting the machine, always check
that all the guards are correctly installed and
adequately protect the blade.
• Check damaged parts.
13