Install The Pump - Thetford SANICON TURBO 500 S Manual Del Propietário

Installation, cont'd.
Ref. Description
K1 Pump Assembly
K2 1.5" Discharge Hose Assembly (One end connects to plumbing,
other end connects to nozzle then RV dump station.)
4A Plumbing (Hard or fl exible pipe) to discharge hose
4B Gate Valves (black, gray, manual over-ride); number of valves
vary according to each coach setup
4C Bayonet RV Drain (manual over-ride)
4D Hose Storage Compartment
4E RV Sidewall
4F RV Sewer Outlet

Install the Pump

Refer to Fig. 1 and Fig. 4.
Recommend Wye or Tee before pump to allow manual
NOTICE
over-ride, easy service access, or to dislodge something
from the pump.
K1.1 Discharge Port
■ 1.25" rubber coupling should be used to connect hard
plumbing to discharge port.
■ Plumbing should be kept as short as possible to increase
pump effi ciency.
■ Spa hose (sold separately) can be attached directly to
the discharge port. A heat gun may be required to install.
K1.3 3" Inlet Port
■ Use rubber coupling
outlet on RV.
■ Support with 3.5" (4" inner diameter) hanger
from pump inlet and use pipe strap
hanger to RV.
K2.1 Discharge Hose Cuff
■ Hose cuff accepts 1.5" hose barb, should be clamped
with supplied clamp .
■ Hose barb (not supplied) should be securely fastened
inside of discharge hose compartment.
®
SANICON Turbo - Model 500
4E
K2
(K6) to connect pump to sewer
(K7)
(K8) to attach
4D
K1
4B
4A
Fig. 4
Prepare
■ Flush all debris from holding tanks.
■ Verify that installed unit will not interfere with the operation
of the gray and black water RV dump valve handles
■ Verify that installed unit will not extend beyond side wall of
coach (4E)
Install
NOTICE AVISO CAUTION AVIS
!
1. Cut back sewer outlet
bayonet fi tting or farther up if the layout allows it.
2. Attach the 3" rubber coupling
3. Place the 3.5" (4" inner diameter) pipe hanger
the rubber coupling
4. Insert the pump
tighten the hose clamps and pipe hanger.
5. Use fasteners
pipe hanger
the RV to support the weight of the pump.
6. Attach plumbing (not provided)
and route to the hose storage compartment.
■ Plumbing should be kept as short as possible to in-
crease pump efficiency.
■ Grey water bypass can be achieved by plumbing the
discharge line in a manner that gravity can allow liquid
to flow to the hose with no upward plumbing.
7. Terminate outlet plumbing with a 1.5" hose barb (not pro-
1"
vided) inside the hose storage compartment.
8. Attach the hose
hose barb with the supplied clamp.
9. Check system for leaks using water.
5
4F
4C
.
Do not cut the plumbing before the gray and black water
tie together or before the gate valves
(4F) on the RV just before the
(K6) to the sewer outlet.
(K6) .
into the rubber coupling
(K1)
(K8.1) to attach the pipe strap
(K7) and fasten the strap to the underside of
to the pump outlet
(4A)
and nozzle assembly to the 1.5"
(K2)
97572 Rev. B (07/10/2017)
(4B) .
(K7) over
and
(K6)
(K8) to the