Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

or
fig 1
1
3
2
fig 2
1
3
2
fig 3
6

System setup

Connecting to your amplifier
AV setup
The e series speakers are suitable for
In a multi-channel system it is
bi-wiring and will benefit from careful
recommended that you use the bass
selection of partnering cables from your
management facilities on your AV amplifier.
amplifier. When bi-wiring, or bi-amping (fig 1),
As the subwoofer is best employed to
remove the connecting links from between
reproduce bass, all low frequency
the terminals at the rear of the speaker.
information should be directed to the
subwoofer enabling the main speakers to
To connect using bare wires (fig 2), strip
reproduce upper bass, midrange and treble
10mm (1/2 inch) of insulation from each
with optimum clarity.
cable. Loosen the terminal caps on the
speaker terminals to reveal the cross holes.
If you are using the bass management of an
Twist the bared conductors together and
AV amplifier, set all speakers to SMALL in
pass through the cross hole in the speaker
your amplifier's speaker configuration and
terminal, securing by screwing down the
set SUBWOOFER to ON. Where the crossover
terminal cap.
frequency can be chosen set it to 80Hz.
Alternatively choose the preset configuration
To connect using spade terminals (fig 3),
for THX.
loosen the terminal caps on the speaker
terminals enough to locate the spades.
Set the Low Pass Crossover Frequency
Tighten the terminal caps onto the spades
control on the subwoofer to 140Hz (on the
so that they are held securely.
e8as2 set the LFE switch to ON). Adjust the
volume control to its mid position.
Connect the positive speaker outlets on the
rear of your amplifier to the positive (red)
Use the distance parameters in your AV
terminals on the rear of the speakers.
amplifier speaker setup to set the distance
Similarly connect the negative speaker
from each set of speakers to your listening
outputs to the negative (black) terminals on
position.
the speakers. Note that speaker cables
usually identify the positive conductor by
Use the channel level adjustment in your AV
marking it with a stripe or raised ridge or
amplifier speaker setup to set the individual
coloured band.
output from each speaker. If you have a
sound level meter adjust the individual level
e
e
as
as
8
1 /
8
2
of each channel for a reading of 75dB at the
listening position. If you do not have access
To connect a stereo hi-fi amplifier it is
to a sound level meter, set the channel
recommended that you connect the speaker
levels so that they sound equally loud at the
outputs of your amplifier to the speaker level
listening position.
inputs of the subwoofer in parallel to the
connections made to your speakers.
Stereo setup
In a hi-fi system without bass management
To connect an AV multi-channel amplifier it
you must adjust the LOW PASS CROSSOVER
is recommended that you connect the LFE
control on the subwoofer in conjunction with
line level input on the subwoofer to the
the SUBWOOFER VOLUME control to achieve
subwoofer output on your amplifier using an
a blend to your main speakers. The e8as1
RCA phono lead (not supplied).
and e8as2 subwoofers can be used with
the e82 and e83 floorstanding speakers in a
Power —Set the subwoofer's ON/OFF switch
hi-fi system. (Note that the e80 is not
to "Off." Then plug the power cord into an
suitable for use in a hi-fi system without
AC outlet. You can turn the power on and off
bass management).
manually using the switch, or you can leave
the mains power turned on and set the Auto
Power switch to "On," which will turn the
subwoofer on automatically when a signal
is detected at one of the inputs and off after
a period of inactivity.
For the e82 speakers, start by setting the
LOW PASS CROSSOVER control to midway
and adjust the SUBWOOFER volume level to
provide a natural level of bass support
when playing music discs. For the e83
speakers, start by setting the LOW PASS
CROSSOVER control to between the 40Hz
and the midway position.
Adjusting the controls
Once you have completed the settings you
should prepare to fine-tune the subwoofer
controls. Choose a multi-channel disc with
natural bass qualities - a music disc is best.
Adjust the control on the subwoofer's rear
panel marked PHASE to tune the blend
between the subwoofer and speakers.
Depending on your room acoustics the
sound will be fuller and more coherent with
the switch in the 0° or 180° position. Use
your judgement to set the switch to the best
sounding position.
On the e8as2 you also have fine control
over phase. Use the variable PHASE control
to achieve the fullest and clearest bass
response. In conjunction with the PHASE
switch, the phase can be varied over 180°.
Adjust the SUBWOOFER VOLUME control to
give bass output that is in balance with your
main speakers. Initially you may prefer the
subwoofer output at a relatively high level,
but this can become tiring, with an over-
emphasis on bass on extended listening.
Turn the volume down by degrees until the
subwoofer is not heard individually but
rather as an extension to the main
speakers.
On the e8as2 you can fine tune the bass
performance to suit your room. If the bass is
boomy, or appears uncontrolled at very low
frequencies, switch the SUBSONIC FILTER to
ON. Adjust the BASS CONTOUR to control
output at the very low frequencies.
7

Publicidad

Tabla de contenido
loading

Productos relacionados para Mission Elegante Serie

Este manual también es adecuado para:

E80E81E82E83E8cE8as1 ... Mostrar todo

Tabla de contenido