Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the
outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this
condition should be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole
means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and
unplug the Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug™ on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be
removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace,
repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device
incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one
way. Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety fea-
ture. If the plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these
devices may overheat and cause a fire hazard.
•DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire
hazard.
•ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•DO NOT block, cover or obstruct air flow to or from the fan while in operation.
•DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location
may create a shock hazard.
•DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•NEVER use a single extension cord to operate more than one Fan or other electrical device.
•DO NOT use this Fan if it has been damaged or is not functioning properly.
•Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
•Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous
locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient
or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the
user's authority to operate this equipment.
SAVE THESE INSTRUCTIONS
NEW 12/17
2
ENSAMBLAJE
1. Para un ensamblaje fácil, coloque el ventilador sobre
una superficie suave.
2. Ubique el cable eléctrico en la parte inferior del
ventilador. Coloque el cable eléctrico dentro del canal
del cable en el Apoyo de columna. (Figura 1)
3. Conecte el Ensamblaje de soporte de columna al
encajar las dos mitades de la columna e insertarla en
la parte inferior del ventilador. (Figura 1)
4. Voltee el ventilador hacia abajo y alinee las flechas
en la columna y la parte inferior del ventilador. Gire en
el sentido de las agujas del reloj para bloquearlo.
Utilice un tornillo de mariposa para fijar la columna al
ventilador. (Figura 2)
5. Arme la base interconectando las salientes en la base
de apoyo A dentro de los orificios de salientes en la
base de apoyo B. Introduzca el cable eléctrico a través
del orificio grande en el centro del ensamblaje de la
base de apoyo. (Figura 3)
6. Conecte la base a la columna y fije con tornillos de
mariposa. (Figura 4)
Conjunto De Soportes De Columna
Soportes De Columna
Cable Eléctrico
Figura 1
Parte trasera
del ventilador
Flecha de
Flecha de
alineación
alineación
Columna
Figura 2
Base de
Soporte B
Figura 3
T38305MES
NEW 12/17
Conjunto de Columna Para la Base
Conjunto de la
Base de Soporte
Tornillo de
mariposa
Figura 4
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los Controles
Manuales ubicados en la parte superior de la unidad o con el
Control Remoto (se muestra en la Figura 5).
1. Coloque el ventilador sobre una superficie firme y nivelada.
2. Conecte el cable eléctrico a un tomacorriente de 120 voltios.
Base Del Motor
3. Conecte la energía eléctrica a su ventilador pulsando el Botón
Alimentación ( ).
4. VELOCIDAD DEL VENTILADOR: Ahora puede ajustar la velo-
cidad del ventilador al nivel deseado - , 2 (mediana) ó 1 (baja)
- pulsando el Botón Velocidad ( ).
5. OSCILACIÓN: Oprima el Botón de Oscilación ( ) para activar y
desactivar la función de oscilación.
6. FUNCIÓN DE TEMPORIZADOR: Este ventilador está equipado
con un temporizador. El temporizador puede ser programado
1 hora a 7 horas. Continúe oprimiendo el Botón Temporiza-
dor ( ) para lograr el tiempo de programación deseado. Para
cancelar el temporizador, presione el botón del temporizador
hasta que se apague la luz.
7. Después de apagar el Ventilador, desconecte la unidad del toma-
corriente eléctrico.
Oscilación
Botón
Tornillo
de
mariposa
Conjunto de la Base de Soporte
Vista des de Arriba
Base de
Soporte A
Copas
7
Conjunto De
Soportes De Columna
Canal Conductor de
Cable
Botón
Botón
Alimentación
Temporizador
Botón
Velocidad
T38305MES
Publicidad
